Number of ports/card |
4 |
Total ports/system |
64 |
Max. boards/system |
16 |
Microprocessor |
Intel® 80C188 |
Digital signal processor |
Motorola DSP56001 @ 20 Mhz, 24-bit |
Host Interface | |
Bus compatibility |
IBM PC XT/AT (ISA) |
Bus speed |
4-12 Mhz, 70 nsec back-to-back bus cycle |
Shared memory |
8 KB page, switch selectable on 8 KB boundaries |
Base addresses |
D000h (default), A000h or C000h |
Interrupt level |
IRQ2 to IRQ7 jumper selectable. One IRQ is shared by all D/42D-SX boards. |
Telephone Interface | |
Support |
MITEL Superset Line Circuit board in a Mitel Superswitch PBX |
Impedance |
600 Ohms nominal |
Receive signal/noise ratio |
70 dBm, referenced to -15 dBm |
Cross talk coupling |
-70 dB at 1KHz channel to channel |
Frequency response |
300Hz to 3400Hz ±3dB (transmit and receive) |
Connectors |
2 RJ-14 type |
Power Requirements | ||
+5 VDC |
1.25 A | |
+12 VDC |
40 mA | |
12 VDC |
40 mA | |
Operating temperature |
0ºC to +50ºC | |
Storage temperature |
-20ºC to +70ºC | |
Humidity |
8% to 80% noncondensing | |
Form Factor | ||
PC XT, 13.3 in. long. 0.774 in. wide, 3.85 in. high (excluding edge connector) | ||
Safety & EMI Certifications | ||
United States |
FCC part 68 ID#: not required UL: E96804 | |
Canada |
DOC: not required CSA: LR-84340-14 | |
Audio Signal | ||
Transmit |
9 dBm (weighted average)** | |
Receive range |
42 to +2.5 dBm | |
Silence detection |
38 dBm, software adjustable** | |
Frequency response |
24 Kb/s300 Hz to 2600 Hz ± 3 dB 32 Kb/s: 300 Hz to 3400 Hz ± 3 dB 48 Kb/s: 300 Hz to 2600 Hz ± 3 dB 64 Kb/s: 300 Hz to 3400 Hz ± 3 dB | |
Audio Digitizing | ||
Method |
OKI ADPCM, Mu-law PCM | |
Sampling rates |
6 kHz, 8 kHz | |
Data rates |
OKI ADPCM: 24 Kb/s, 32 Kb/ Mu-law PCM: 48 Kb/s, 64 Kb/s | |
Tone Dialing | ||
DTMF digits |
0 to 9, *, #, A, B, C, D | |
MF digits |
0 to 9, KP, ST, ST1, ST2, ST3 | |
Level |
Network compatible | |
Rate |
10 digits/s maximum, software adjustable | |
Pulse Dialing | ||
10 digits |
0 to 9 | |
Pulsing rate |
10 pulses/s, nominal | |
Break ratio |
60% | |
DTMF Tone Detection: | ||
DTMF digits |
0 to 9, *, #, A, B, C, D per Bellcore LSSGR Sec 6 | |
Dynamic range |
-36 dBm to +0 dBm per tone** | |
Minimum tone duration |
32 ms, software adjustable | |
Acceptable twist |
Meets Bellcore LSSGR Sec 6 and EIA 464 requirements | |
Signal/noise ratio |
10 dB (referenced to lowest amplitude tone) | |
Talk off |
Detects 0 digits while monitoring MITEL speech tape #CM7291. Detects less than 10 digits while monitoring Bellcore TR-TSY-000763 standard speech tapes (LSSGR requirements specify detecting no more than 470 total digits). | |
MF Tone Detection | ||
MF digits |
0 to 9, KP, ST, ST1, ST2, ST3 | |
Speed Control | ||
Pitch controlled |
Available for 24 and 32 Kb/s data rates | |
Adjustment range |
50% | |
Volume Control | ||
Adjustment range |
40 dB, with programmer-definable increments | |
* All specifications are subject to change without notice.
**Analog levels: 0 dBm0 corresponds to a level of +3dBm at tip-ring analog point.
System RequirementsD/42D-SLTechnical Specifications*
Number of ports/card |
4 |
Total ports/system |
64 |
Max. boards/system |
16 |
Microprocessor |
Intel® 80C188 |
Digital signal processor |
Motorola DSP56001 @ 20 Mhz, 24-bit |
Host Interface | |
Bus compatibility |
IBM PC XT/AT (ISA) |
Bus speed |
4-12 Mhz, 70 nsec back-to-back bus cycle |
Shared memory |
8 KB page, switch selectable on 8 KB boundaries |
Base addresses |
D000h (default), A000h or C000h |
Interrupt level |
IRQ2 to IRQ7 jumper selectable. One IRQ is shared by all D/42D-SL boards. |
Telephone Interface | |
Support |
Northern Telecom SL-1 line circuit board; QPC61, 4 circuit; QPC451, 8 circuit |
Impedance |
600 Ohms nominal |
Receive signal/noise ratio |
70 dBm, referenced to -15 dBm |
Cross talk coupling |
-70 dB at 1KHz channel to channel |
Frequency response |
300Hz to 3400Hz ±3dB (transmit and receive) |
Connectors |
4 RJ-14 type |
Power Requirements | |
+5 VDC |
1.25 A |
+12 VDC |
40 mA |
-12 VDC |
40 mA |
Operating temperature |
0ºC to +50ºC |
Storage temperature |
-20ºC to +70ºC |
Humidity |
8% to 80% noncondensing |
Form Factor | |
PC XT, 13.3 in. long. 0.774 in. wide, 3.85 in. high (excluding edge connector) | |
Safety & EMI Certifications | |
United States |
FCC part 68 ID#: not required UL: E96804 |
Canada |
DOC: not required CSA: LR-84340-14 |
Warranty |
36 months standard |
Firmware Specifications*
Audio Signal | |
Transmit |
-9 dBm (weighted average)** |
Receive range |
-42 to +2.5 dBm |
Silence detection |
-38 dBm, software adjustable** |
Frequency response |
24 Kb/s: 300 Hz to 2600 Hz ±3 dB 32 Kb/s: 300 Hz to 3400 Hz ±3 dB 48 Kb/s: 300 Hz to 2600 Hz ±3 dB 64 Kb/s: 300 Hz to 3400 Hz ±3 dB |
Audio Digitizing | |
Method |
OKI ADPCM, Mu-law PCM |
Sampling rates |
6 kHz, 8 kHz |
Data rates |
OKI ADPCM: 24 Kb/s, 32 Kb/s Mu-law PCM: 48 Kb/s, 64 Kb/s |
Tone Dialing | |
DTMF digits |
0 to 9, *, #, A, B, C, D |
MF digits |
0 to 9, KP, ST, ST1, ST2, ST3 |
Level |
Network compatible |
Rate |
10 digits/s maximum, software adjustable |
Pulse Dialing | |
10 digits |
0 to 9 |
Pulsing rate |
10 pulses/s, nominal |
Break ratio |
60% |
DTMF Tone Detection | |
DTMF digits |
0 to 9, *, #, A, B, C, D per Bellcore LSSGR Sec 6 |
Dynamic range |
-36 dBm to +0 dBm per tone** |
Minimum tone duration |
32 ms, software adjustable |
Acceptable twist |
Meets Bellcore LSSGR Sec 6 and EIA 464 requirements |
Signal/noise ratio |
10 dB (referenced to lowest amplitude tone) |
Talk off |
Detects 0 digits while monitoring MITEL speech tape #CM7291. Detects less than 10 digits while monitoring Bellcore TR-TSY-000763 standard speech tapes (LSSGR requirements specify detecting no more than 470 total digits). |
MF Tone Detection | |
MF digits |
0 to 9, KP, ST, ST1, ST2, ST3 |
Speed Control | |
Pitch controlled |
Available for 24 and 32 Kb/s data rates |
Adjustment range |
50% |
Volume Control | |
Adjustment range |
40 dB, with programmer-definable increments |
* All specifications are subject to change without notice.
** Analog levels: 0 dBm0 corresponds to a level of +3dBm at tip-ring analog point.
ComponentsAdditional components include
Cable connecting D/42D-SL board to SL-1 board:
System RequirementsD/42-NSTechnical Specifications*
Number of ports/card |
4 |
Total ports/system |
64 |
Max. boards/system |
16 |
Resource sharing bus |
PEB |
Microprocessor |
Intel® 80C188 |
Digital signal processor |
Motorola DSP56001 @ 27 Mhz, 24-bit |
Host Interface | |
Bus compatibility |
IBM PC XT/AT (ISA), 16 bit |
Bus speed |
4-12 Mhz, 70 nsec back-to-back bus cycle |
Shared memory |
8 KB page, switch selectable on 8 KB boundaries |
Base addresses |
D000h (default), A000h or C000h |
Interrupt level |
IRQ3 to IRQ15 jumper selectable. One IRQ is shared by all D/42-NS boards. |
Telephone Interface | |
Meets all specifications set by Northern Telecom for the Norstar TCM station interface. | |
Connectors |
4 RJ-11 type |
Power Requirements | |
+5 VDC ± 5% |
2.0 A |
Operating temperature |
0ºC to +50ºC |
Storage temperature |
-20ºC to +70ºC |
Humidity |
8% to 80% noncondensing |
Form Factor | |
PC XT/AT, 13.3 in. long. 0.774 in. wide, 3.85 in. high (excluding edge connector) | |
Safety & EMI Certifications | |
United States |
FCC part 68 does not apply |
Canada |
CSO3 does not apply |
Warranty |
36 months standard |
Firmware Specifications*
Audio Signal | |
Transmit |
-12.5 dBm0 (weighted average)** |
Receive range |
-42 to +2.5 dBm |
Silence detection |
-38 dBm0, software adjustable** |
Frequency response |
24 Kb/s: 300 Hz to 2600 Hz ±3 dB 32 Kb/s: 300 Hz to 3400 Hz ±3 dB 48 Kb/s: 300 Hz to 2600 Hz ±3 dB 64 Kb/s: 300 Hz to 3400 Hz ±3 dB |
Audio Digitizing | |
Method |
OKI ADPCM, Mu-law PCM |
Sampling rates |
6 kHz, 8 kHz |
Data rates |
OKI ADPCM: 24 Kb/s, 32 Kb/s Mu-law PCM: 48 Kb/s, 64 Kb/s |
Tone Dialing: | |
DTMF digits |
0 to 9, *, #, A, B, C, D |
MF digits |
0 to 9, KP, ST, ST1, ST2, ST3 |
Level |
Network compatible |
Rate |
10 digits/s maximum, software adjustable |
Pulse Dialing | |
10 digits |
0 to 9 |
Pulsing rate |
10 pulses/s, nominal |
Break ratio |
60% |
DTMF Tone Detection: | |
DTMF digits |
0 to 9, *, #, A, B, C, D per Bellcore LSSGR Sec 6 |
Dynamic range |
-39 dBm0 to +0 dBm0 per tone** |
Minimum tone duration |
32 ms, software adjustable |
Acceptable twist |
Meets Bellcore LSSGR Sec 6 and EIA 464 requirements |
Signal/noise ratio |
10 dB (referenced to lowest amplitude tone) |
Talk off |
Detects 0 digits while monitoring MITEL speech tape #CM7291. Detects less than 10 digits while monitoring Bellcore TR-TSY-000763 standard speech tapes (LSSGR requirements specify detecting no more than 470 total digits). |
MF Tone Detection: | |
MF digits |
0 to 9, KP, ST, ST1, ST2, ST3 |
Speed Control | |
Pitch controlled |
Available for 24 and 32 Kb/s data rates |
Adjustment range |
50% |
Volume Control | |
Adjustment range |
40 dB, with programmer-definable increments |
*All specifications are subject to change without notice.
** Digital levels: 0 dBm0 corresponds with 3 dB below Mu-law full scale on digital PEB products.
System Requirements* These are obsolete software revisions and may contain limitations. Dialogic recommends that switch software be upgraded to the DR5 Maintenance Release.
D/42-NE2Technical Specifications*
Number of ports/card |
4 |
Resource-sharing bus |
PEBTM |
Microprocessor |
Intel 80C188 |
Digital signal processor |
Motorola DSP56001 |
Host Interface | |
Bus compatibility |
IBM PC AT |
Bus speed |
4-12 Mhz, minimum 70 nsec back-to-back bus cycle |
Shared memory |
8 KB, switch selectable on 8 KB boundaries |
Base addresses |
D000H (default), A000H, C000H |
Maximum boards/system |
16 |
Interrupt level |
IRQ3 to IRQ15, jumper selectable. One IRQ shared by all boards. |
Telephone interface | |
meets all specifications set by NEC for the 2-wire Dterm Series III PBX Telephone and the 2-wire Electra Professional Key System Telephone | |
Connectors: |
4 RJ-11 type |
Power Requirements: | |
+5 Vdc |
2.5 A |
Environmental | |
Operating temperature |
0°C to +50°C |
Storage temperature |
20°C to +70°C |
Humidity |
8% to 80% noncondensing |
Form factor | |
PC XT/AT, 13.3 in. long. 0.774 in. wide, 3.85 in. high (excluding edge connector) | |
Safety & EMI Certifications | |
United States |
FCC part 68 does not apply |
Canada |
CSO3 does not apply |
Warranty |
36 months standard |
Firmware Specifications*
Audio Signal | |
Transmit |
-12.5 dBm0 (weighted average)** |
Receive range |
-63 to +2.5 dBm0 (AGC above -21 dBm0)** |
Silence detection |
-41 dBm0, software adjustable** |
Frequency response |
24 Kb/s: 300 Hz to 2600 Hz ± 3 dB 32 Kb/s: 300 Hz to 3400 Hz ± 3 dB 48 Kb/s: 300 Hz to 2600 Hz ± 3 dB 64 Kb/s: 300 Hz to 3400 Hz ± 3 dB |
Audio Digitizing: | |
Method |
ADPCM, _-law PCM |
Sampling rates |
6 kHz, 8 kHz |
Data Rates |
ADPCM: 24 Kb/s, 32 Kb/s Mu-law PCM: 48 Kb/s, 64 Kb/s |
Tone Dialing: | |
DTMF digits |
0 to 9, *, #, A, B, C, D |
MF digits |
0 to 9, KP, ST, ST1, ST2, ST3 |
Level |
Network compatible |
Rate |
10 digits/s maximum, software adjustable |
Pulse Dialing: | |
10 digits |
0 to 9 |
Pulsing rate |
10 pulses/s, nominal |
Break ratio |
60% |
DTMF Tone Detection: | |
DTMF digits |
0 to 9, *, #, A, B, C, D |
Dynamic range |
-39 dBm0 to +0 dBm0 per tone** |
Minimum tone duration |
32 ms, software adjustable |
Acceptable twist: |
10 dB |
Signal/noise ratio |
10 dB (referenced to lowest amplitude tone) |
Talk off |
Detects 0 digits while monitoring MITEL speech tape #CM 7291. Detects less than 20 digits while monitoring Bellcore TR-TSY-000763 standard speech tapes (LSSGR requirements specify detecting no more than 470 total digits). |
MF Tone Detection: | |
MF digits |
0 to 9, KP, ST, ST1, ST2, ST3 |
Speed control |
Pitch controlled; available for 24 and 32 Kb/s data rates |
* All specifications are subject to change without notice.
** Digital levels: 0 dBm0 corresponds to 3 dB below _-law full scale on digital PEB products. Analog levels: 0 dBm0 corresponds to a level of +3 dBm at tip-ring analog point.
D/42-NE2 PCITechnical Specifications*
Number of ports/card |
4 |
Resource-sharing bus |
None |
Microprocessor |
Intel 80C188 |
Digital signal processor |
Motorola DSP56002 |
Host Interface | |
Bus compatibility |
PCI Local Bus |
Bus speed |
33 MHz |
Shared memory |
8 KB |
Base address |
D0000 (default) |
Maximum boards/system |
16 |
Interrupt level |
INTA |
Telephone interface | |
Meets all specifications set by NEC for the 2-wire Dterm Series III PBX Telephone and the 2-wire Electra Professional Key System Telephone | |
Connectors: |
4 RJ-11 type |
Power Requirements: | |
+5 Vdc |
2.5 A |
Environmental | |
Operating temperature |
0°C to +50°C |
Storage temperature |
-20°C to +70°C |
Humidity |
8% to 80% noncondensing |
Form factor | |
PCI short format card, 6.875 in. long. 0.79 in. wide, 4.2 in. high (excluding edge connector). | |
Safety & EMI Certifications | |
United States |
FCC part 68 does not apply |
Canada |
CSO3 does not apply |
Warranty |
36 months standard |
Firmware Specifications*
Audio Signal | |
Transmit |
-12.5 dBm0 (weighted average)** |
Receive range |
-63 to +2.5 dBm0 (AGC above -21 dBm0)** |
Silence detection |
-41 dBm0, software adjustable** |
Frequency response |
24 Kb/s: 300 Hz to 2600 Hz ± 3 dB 32 Kb/s: 300 Hz to 3400 Hz ± 3 dB 48 Kb/s: 300 Hz to 2600 Hz ± 3 dB 64 Kb/s: 300 Hz to 3400 Hz ± 3 dB |
Audio Digitizing: | |
Method |
ADPCM, _-law PCM |
Sampling rates |
6 kHz, 8 kHz |
Data Rates |
ADPCM: 24 Kb/s, 32 Kb/s Mu-law PCM: 48 Kb/s, 64 Kb/s |
Tone Dialing: | |
DTMF digits |
0 to 9, *, #, A, B, C, D |
MF digits |
0 to 9, KP, ST, ST1, ST2, ST3 |
Level |
Network compatible |
Rate |
10 digits/s maximum, software adjustable |
Pulse Dialing: | |
10 digits |
0 to 9 |
Pulsing rate |
10 pulses/s, nominal |
Break ratio |
60% |
DTMF Tone Detection: | |
DTMF digits |
0 to 9, *, #, A, B, C, D |
Dynamic range |
-39 dBm0 to +0 dBm0 per tone** |
Minimum tone duration |
32 ms, software adjustable |
Acceptable twist: |
10 dB |
Signal/noise ratio |
10 dB (referenced to lowest amplitude tone) |
Talk off |
Detects 0 digits while monitoring MITEL speech tape #CM 7291. Detects less than 20 digits while monitoring Bellcore TR-TSY-000763 standard speech tapes (LSSGR requirements specify detecting no more than 470 total digits). |
MF Tone Detection: | |
MF digits |
0 to 9, KP, ST, ST1, ST2, ST3 |
Speed control |
Pitch controlled; available for 24 and 32 Kb/s data rates |
* All specifications are subject to change without notice.
** Digital levels: 0 dBm0 corresponds to 3 dB below _-law full scale on digital PCI products. Analog levels: 0 dBm0 corresponds to a level of +3 dBm at tip-ring analog point.
Click here to contact Dialogic Customer Engineering
Copyright 1999, Dialogic Corporation