1.9.2. Set Configuration of Digital Subscriber Loop (BRI Only)

Note: This functionality is supported when using Springware boards only; not supported when using DM3 boards.

Parameter	Input
target_type	GCTGT_CCLIB_NETIF
target_id	board device handle
GC_PARM_BLK	set_id - GCIS_SET_DCHANCFG
	parm_id - GCIS_PARM_DCHANCFG_L2ACCESS
	values - LAYER_2_ONLY: ISDN access at layer 2. If this is selected then no other parameters are required. FULL_ISDN_STACK: ISDN access at L3 call control.
	value_type - char
	parm_id - GCIS_PARM_DCHANCFG_SWITCHTYPE
	values - ISDN_BRI_5ESS = ATT 5ESS BRI ISDN_BRI_DMS100 = Northern Telecom DMS100 BRI ISDN_BRI_NTT = Japanese INS-Net 64 BRI ISDN_BRI_NET3 = EuroISDN BRI ISDN_BRI_NI1 = National ISDN 1 ISDN_BRI_NI2 = National ISDN 2
	value_type - char
	parm_id - GCIS_PARM_DCHANCFG_SWITCHSIDE
	values - USER_SIDE = User side of ISDN protocol NETWORK_SIDE = Network side of ISDN protocol
	value_type - char
	parm_id - GCIS_PARM_DCHANCFG_NUMENDPOINTS
	values - 1 to MAX_DLINK range, where MAX_DLINK is currently set to 8.
	value_type - char
	parm_id - GCIS_PARM_DCHANCFG_FIRMWARE_FEATUREMASKA
	values - NO_PCM_TONE ULAW_PCM_TONE ALAW_PCM_TONE DEFAULT_PCM_TONE SENDING_COMPLETE_ATTACH USER_PERST_L2_ACT HOST_CONTROLLED_RELEASE
	value_type - char
	parm_id - GCIS_PARM_DCHANCFG_TEIASSIGNMENT
	values - AUTO_TEI_TERMINAL = auto TEI assigning Term FIXED_TEI_TERMINAL = Fixed TEI assigning Term
	value_type - char
	parm_id - GCIS_PARM_DCHANCFG_FIXEDTEIVALUE
	values - range 0 to 63
	value_type - char
	parm_id - GCIS_PARM_DCHANCFG_AUTOINITFLAG
	values - AUTO_INIT_TERMINAL NON_INIT_TERMINAL
	value_type - char
	parm_id - GCIS_PARM_DCHANCFG_SPID
	value - ASCII digit string limited to the digits 0-9 and limited in length to MAX_SPID_SIZE
	value_type - string
	parm_id - GCIS_PARM_DCHANCFG_TMR302 GCIS_PARM_DCHANCFG_TMR303 GCIS_PARM_DCHANCFG_TMR304 GCIS_PARM_DCHANCFG_TMR305 GCIS_PARM_DCHANCFG_TMR306 GCIS_PARM_DCHANCFG_TMR308 GCIS_PARM_DCHANCFG_TMR309 GCIS_PARM_DCHANCFG_TMR310 GCIS_PARM_DCHANCFG_TMR312 GCIS_PARM_DCHANCFG_TMR313 GCIS_PARM_DCHANCFG_TMR318 GCIS_PARM_DCHANCFG_TMR319 GCIS_PARM_DCHANCFG_TMR322
	values - See Q.931 specification and corresponding switch specifications for exact definitions and default values for these timers. Not all timers are applicable to all of the switches. Specified values are in 10 millisecond increments. For example, a specified value of 100 is equivalent to 1 second. Possible values are: 0 = Default value for switch -1 = Default value for switch
	value_type - long
mode	EV_SYNC or EV_ASYNC
update condition	GCUPATE_IMMEDIATE (gc_SetConfigData( ) function only)

Click here to contact Telecom Support Resources