HPE INTERNAL USE ONLY

Analysis Code: 3003

Severity: Info

INEX is providing this information for informational purposes only.

Use this information to help research vendor specific asc/ascq codes that are being reported in the general event logs from the array.

SEAGATE Vendor Specific Asc/Ascq Codes

SEAGATE Specific Vendor Codes

Table Note. lists the Additional Sense (ASC) and Additional Sense Qualifier (ASCQ) codes. Code values are in hexadecimal. ANSI standard SPC-4 lists a more complete table in error description alphabetical order. This Table Note. list adequately covers all Seagate drives, however.

Note. Table Note. is for reference only, as not all drives covered by this manual support all of the codes listed. Codes without sense key references may or may not be supported.

Table 29 Additional Sense and Additional Sense Qualifier codes

ASC (byte 12)	ASCQ (byte 13)	Description	Sense Key
00	00	No Additional Sense Information	0
01	00	No Index/Logical Block Signal	4
02	00	No SEEK Complete	4
03	00	Peripheral Device Write Fault	1, 3, 4
03	86	Write Fault Data Corruption
04	00	Logical Unit Not Ready, Cause Not Reportable	2
04	01	Logical Unit Not Ready, Becoming Ready	2
04	02	Logical Unit Not Ready, START UNIT Required	2
04	03	Logical Unit Not Ready, Manual Intervention Required	2
04	04	Logical Unit Not Ready, Format in Progress	2
04	09	Logical Unit Not Ready, Self Test in Progress	2
04	0A	Logical Unit Not Ready, NVC recovery in progress after and exception event	2
04	11	Logical Unit Not Ready, Notify (Enable Spinup) required	2
04	F0	Logical unit not ready, super certify in progress	2
08	00	Logical Unit Communication Failure	9, B
08	01	Logical Unit Communication Time-Out	B
08	02	Logical Unit Communication Parity Error
09	00	Track Following Error	1, 3, 4
09	01	Servo Fault	1, 4
09	04	Head Select Fault	3, 4
09	0D	Write to at least one copy of a redundant file failed	1
09	0E	Redundant files have < 50% good copies	1
09	F8	Calibration is needed but the QST is set without the Recal Only bit	1
09	FF	Servo Cal completed as part of self-test	1
0A	00	Error Log Overflow
0A	01	Failed to write super certify log file	3
0A	02	Failed to read super certify log file	3
0B	00	Aborted Command	B
0B	01	Warning—Specified Temperature Exceeded	1, 6
0B	02	Warning, Enclosure Degraded	1

ASC (byte 12)	ASCQ (byte 13)	Description	Sense Key
0C	00	Write Error	3
0C	01	Write Error Recovered With Auto-Reallocation	1
0C	02	Write Error—Auto Reallocation Failed	3
0C	03	Write Error—Recommend Reassignment	3
0C	FF	Write Error—Too many error recovery revs	3
0D	00	Volume Overflow Constants	D
0E	00	Data Miscompare	E
10	00	ID CRC Or ECC Error
11	00	Unrecovered Read Error	1, 3
11	01	Read Retries Exhausted
11	02	Error Too Long To Correct
11	04	Unrecovered Read Error—Auto Reallocation Failed	3
11	FF	Unrecovered Read Error—Too many error recovery revs	3
12	00	Address Mark Not Found For ID Field
12	01	Recovered Data Without ECC Using Previous Logical Block ID
12	02	Recovered Data With ECC Using Previous Logical Block ID
14	00	Logical Block Not Found
14	01	Record Not Found	3
15	00	Random Positioning Error
15	01	Mechanical Positioning Error	1, 3, 4
15	02	Positioning Error Detected By Read Of Medium
16	00	Data Synchronization Mark Error	1, 3, 4
17	00	Recovered Data With No Error Correction Applied
17	01	Recovered Data Using Retries	1
17	02	Recovered Data Using Positive Offset	1
17	03	Recovered Data Using Negative Offset	1
17	05	Recovered Data Using Previous Logical Block ID
17	06	Recovered Data Without ECC—Data Auto Reallocated
18	00	Recovered Data With ECC	1
18	01	Recovered Data With ECC And Retries Applied	1
18	02	Recovered Data With ECC And/Or Retries, Data Auto-Reallocated	1
18	05	Recovered Data—Recommand Reassignment
18	06	Recovered Data Using ECC and Offsets
18	07	Recovered Data With ECC—Data Rewritten	1
19	00	Defect List Error	1, 4

ASC (byte 12)	ASCQ (byte 13)	Description	Sense Key
19	01	Defect List Not Available
19	02	Defect List Error In Primary List
19	03	Defect List Error in Grown List
19	0E	Fewer than 50% Defect List Copies
1A	00	Parameter List Length Error	5
1B	00	Synchronous Data Transfer Error
1C	00	Defect List Not Found	1, 4
1C	01	Primary Defect List Not Found
1C	02	Grown Defect List Not Found
1C	83	Seagate Unique Diagnostic Code
1D	00	Miscompare During Verify Operation	E
1F	00	Number of Defects Overflows the Allocated Space That The Read Defect Command Can Handle	1
20	00	Invalid Command Operation Code	5
20	F3	Invalid linked command operation code	5
21	00	Logical Block Address Out Of Range	D
24	00	Invalid Field In CDB	5
24	01	Illegal Queue Type for CDB (Low priority commands must be SIMPLE queue)	5
24	F0	Invalid LBA in linked command	5
24	F2	Invalid linked command operation code	5
24	F3	Illegal G->P operation request	5
25	00	Logical Unit Not Supported	5
26	00	Invalid Field In Parameter List	5
26	01	Parameter Not Supported	5
26	02	Parameter Value Invalid	5
26	03	Invalid Field Parameter—Threshold Parameter	5
26	04	Invalid Release of Active Persistent Reserve	5
26	05	Fail to read valid log dump data	5
26	97	Invalid Field Parameter—TMS Firmware Tag
26	98	Invalid Field Parameter—Check Sum
26	99	Invalid Field Parameter—Firmware Tag
27	00	Write Protected	7
29	00	Flashing LED occurred	4
29	00	Power On, Reset, Or Bus Device Reset Occurred	6
29	01	Power-On Reset Occurred	6
29	02	SCSI Bus Reset Occurred	6

ASC (byte 12)	ASCQ (byte 13)	Description	Sense Key
29	03	Bus Device Reset Function Occurred	6
29	04	Internal Reset Occurred	6
29	05	Transceiver Mode Changed To Single-Ended	6
29	06	Transceiver Mode Changed To LVD	6
29	07	Write Log Dump data to disk successful OR IT Nexus Loss	6
29	08	Write Log Dump data to disk fail	6
29	09	Write Log Dump Entry information fail	6
29	0A	Reserved disk space is full	6
29	0B	SDBP test service contained an error, examine status packet(s) for details	6
29	0C	SDBP incoming buffer overflow (incoming packet too big)	6
29	CD	Flashing LED occurred. (Cold reset)	6
29	CE	Flashing LED occurred. (Warm reset)	6
2A	01	Mode Parameters Changed	6
2A	02	Log Parameters Changed	6
2A	03	Reservations preempted	6
2A	04	Reservations Released	6
2A	05	Registrations Preempted	6
2C	00	Command Sequence Error	5
2F	00	Tagged Commands Cleared By Another Initiator	6
31	00	Medium Format Corrupted	3
31	01	Corruption in R/W format request	3
31	91	Corrupt World Wide Name (WWN) in drive information file	3
32	00	No Defect Spare Location Available	4
32	01	Defect List Update Error	3, 4, 5
32	02	No Spares Available—Too Many Defects On One Track
32	03	Defect list longer than allocated memory	3
33	00	Flash not ready for access	3
35	00	Unspecified Enclosure Services Failure	4
35	01	Unsupported Enclosure Function	5
35	02	Enclosure Services Unavailable	2
35	03	Enclosure Transfer Failure	4
35	04	Enclosure Transfer Refused	4
37	00	Parameter Rounded	1
3D	00	Invalid Bits In Identify Message
3E	03	Logical Unit Failed Self Test	4

ASC (byte 12)	ASCQ (byte 13)	Description	Sense Key
3E	00	Logical Unit Has Not Self Configured Yet
3F	00	Target Operating Conditions Have Changed	6
3F	01	Device internal reset occurred	6
3F	02	Changed Operating Definition	6
3F	05	Device Identifier Changed	6
3F	0F	Echo buffer overwritten	B
3F	80	Buffer contents have changed	1
3F	90	Invalid APM Parameters
3F	91	World Wide Name (WWN) Mismatch	6
40	01	DRAM Parity Error	1, 4
40	02	Spinup Error recovered with retries	1
42	00	Power-On Or Self-Test Failure	4
42	0A	Port A failed loopback test	4
42	0B	Port B failed loopback test	4
43	00	Message Reject Error	B
44	00	Internal Target Failure	1, 3, 4
44	F2	Data Integrity Check Failed on verify	4
44	F6	Data Integrity Check Failed during write	4
44	FF	XOR CDB check error	4
45	00	Select/Reselection Failure	B
47	00	SCSI Parity Error	B
47	03	Information Unit CRC Error	B
47	80	Fibre Channel Sequence Error	B
48	00	Initiator Detected Error Message Received	B
49	00	Invalid Message Received	B
4B	00	Data Phase Error	B
4B	01	Invalid transfer tag	B
4B	02	Too many write data	B
4B	03	ACK NAK Timeout	B
4B	04	NAK received	B
4B	05	Data Offset error	B
4B	06	Initiator response timeout	B
4C	00	Logical Unit Failed Self-Configuration
4E	00	Overlapped Commands Attempted	B
55	01	XOR Cache is Not Available

55	04	PRKT table is full	5
5B1	00	Log Exception
5B*	01	Threshold Condition Met
5B*	02	Log Counter At Maximum
5B*	03	Log List Codes Exhausted
5C	00	RPL Status Change	6
5C	01	Spindles Synchronized
5C	02	Spindles Not Synchronized
5D	00	Failure Prediction Threshold Exceeded	1, 6
5D	FF	False Failure Prediction Threshold Exceeded	1, 6
65	00	Voltage Fault	4
80	00	General Firmware Error Qualifier	9
80	86	IOEDC Error on Read	9
80	87	IOEDC Error on Write	9
80	88	Host Parity Check Failed	9
80	89	IOEDC Error on Read Detected by Formatter	9
80	8A	Host FIFO Parity Error detected by Common Buffer	9
80	8B	Host FIFO Parity Error detected by frame buffer logic	9
80	8C	Host Data Frame Buffer Parity Error	9
81	00	Reassign Power—Fail Recovery Failed
81	00	LA Check Error, LCM bit = 0	4
81	00	LA Check Error	B
B4	00	Unreported Deferred Errors have been logged on log page 34h	6

[1] Can be supported, but is a factory installed option.