RRM Profile

Context

WLAN technology uses radio signals (such as 2.4 GHz or 5 GHz radio waves) as transmission medium. Radio waves will attenuate when they are transmitted over air, degrading service quality for wireless users. Radio resource management enables a WLAN to adapt to changes in the radio environment by dynamically adjusting radio resources. This improves service quality for wireless users.

Procedure

Create an RRM profile.

Choose Configuration > Wireless Services > Profile > Radio Management > RRM Profile. The RRM Profile List page is displayed.
Click Create. The Create RRM Profile page is displayed.
Enter the name of the new RRM profile in Profile name.
To copy all parameters from another profile to the new profile, select the name of the profile in Copy parameters from other profiles. If None is selected, parameters are not copied from another profile.
Click OK. The parameter setting page of the new RRM profile is displayed.

Set parameters for creating an RRM profile. Table 1 describes the parameters for creating an RRM profile.

**Table 1** Parameters for creating an RRM profile
Parameter	Description
RRM Profile	Name of the RRM profile, which cannot be modified.
Packet loss ratio threshold triggering partial calibration	Packet loss ratio threshold for triggering channel or power adjustment.
Airtime fair scheduling	Whether to enable airtime fair scheduling.
Dynamic EDCA	Whether to enable dynamic EDCA.
UAC
UAC policy	User CAC policy.
New user count threshold	CAC threshold for new users based on the user quantity.
Roaming user count threshold	CAC threshold for roaming users based on the user quantity.
New user channel usage threshold	CAC threshold for new users based on the channel usage.
Roaming user channel usage threshold	CAC threshold for roaming users based on the channel usage.
Hide SSID when user count threshold is exceeded	Whether to enable an AP to automatically hide its SSID when the number of new users reaches the CAC threshold.
Restrict access of weak-signal STAs	Whether to restrict access from weak-signal STAs.
Threshold for rejecting access of weak-signal STAs	Threshold for rejecting access from weak-signal STAs.
Band Steering
Start threshold for load balancing between frequencies	Start threshold for load balancing between two frequencies on the AP that has band steering enabled.
Load difference threshold for load balancing between frequencies	Load difference threshold for load balancing between two frequencies on the AP that has band steering enabled.
Minimum SNR for inter-frequency load balancing	Start SNR threshold for triggering 5G-prior access.
Maximum number of rejections	Maximum number of times an AP rejects association requests of a STA through band steering.
Probe count for aging STA frequency band	Number of times an AP continuously receives probe frames from the same frequency band.
Dynamic Load Balancing
Load balancing	Whether to enable load balancing.
Maximum number of rejections	Maximum number of times an AP rejects association requests of a STA for dynamic load balancing.
Mode	Dynamic load balancing mode.
Start threshold for load balancing (STA count)	Start threshold for load balancing based on the number of STAs.
Start threshold for load balancing (%)	Start threshold for load balancing based on the channel utilization.
Load difference threshold for load balancing	Load difference threshold for dynamic load balancing.
Smart Roaming
Smart roaming	Whether to enable smart roaming.
Check roaming threshold type	Trigger mode of smart roaming, which can be check SNR or check rate.
SNR threshold	SNR-based roaming threshold.
Rate percentage threshold	Rate-based roaming threshold.
Upper threshold of roaming SNR difference	Upper threshold for triggering STA roaming.
Lower threshold of roaming SNR difference	Lower threshold for triggering STA roaming.
SNR detection interval	SNR detection interval of smart roaming STAs.
Aging time of "unable to roam" record	Aging time of "unable to roam" record of smart roaming STAs.
SNR threshold for forcing low-signal users offline	Specifies the SNR-based threshold for quickly disconnecting STAs.
Rate percentage for forcing low-signal users offline	Specifies the rate-based threshold for quickly disconnecting STAs.

Click Apply. In the Info dialog box that is displayed, click OK.

Modify an RRM profile.
1. Choose Configuration > Wireless Services > Profile > Radio Management > RRM Profile. The RRM Profile List page is displayed.
2. Click the name of the RRM profile that you want to modify. The RRM Profile page is displayed.
3. Modify parameters of the RRM profile. Table 1 describes the parameters for modifying an RRM profile.
4. Click Apply. In the Info dialog box that is displayed, click OK.
Delete an RRM profile.
1. Choose Configuration > Wireless Services > Profile > Radio Management > RRM Profile. The RRM Profile List page is displayed.
2. Select the profile that you want to delete and click Delete. In the Confirm dialog box that is displayed, click OK.
Display the profile reference relationship.
1. Choose Configuration > Wireless Services > Profile > Radio Management > RRM Profile. The RRM Profile List page is displayed.
2. Select the profile of which you want to display the reference relationship and click Display Reference Relationship. The system displays the types and names of the objects that reference the profile.
  NOTE:
  Click Hide Reference Relationship. The system hides the displayed results.