AP Wired Port Profile

Context

An AP wired port profile allows you to manage and configure wired interfaces of APs. You can configure wired port parameters in the AP wired port profile to facilitate AP management.

Procedure

Create an AP wired port profile.

Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
Click Create. The Create AP Wired Port Profile page is displayed.
Enter the name of the new AP wired port profile in Profile name.
To copy all parameters from another profile to the new profile, select the name of the profile in Copy parameters from other profiles. If None is selected, parameters are not copied from another profile.
Click OK. The parameter setting page of the new AP wired port profile is displayed.

Set parameters for creating an AP wired port profile. Table 1 describes the parameters for creating an AP wired port profile.

**Table 1** Parameters for creating an AP wired port profile
Parameter	Description
AP Wired Port Profile	Name of the AP wired port profile, which cannot be modified.
Enable Eth-trunk	Whether to enable Eth-Trunk.
Port mode	Operating mode of a wired interface. None: default mode root: root mode endpoint: endpoint mode middle: middle mode NOTE: By default, On a common AP: Its GE interfaces work in root mode, Eth interfaces in endpoint mode, and Eth-Trunk interfaces in root mode. On a central AP: Its downlink GE interfaces work in middle mode and uplink GE interfaces in root mode. On an R230D: Its Eth interface works in root mode. On an R240D: Its Eth interface works in endpoint mode and GE interface in root mode. On an R450D: Its GE interface works in root mode. On an R250D, R250D-E, AP2050DN, and AP2050DN-E: Their uplink GE interfaces work in root mode and downlink GE interfaces in endpoint mode.
Port description	Port description.
User isolation mode	User isolation mode on a wired interface. If Port mode is set to endpoint, you need to set this parameter.
STP	Whether to enable STP on the wired interface.
STP-triggered port shutdown	Whether STP-triggered port shutdown is enabled on the AP's wired interface.
Port recovery time	Auto-recovery interval for an AP's wired interface on which the STP-triggered port shutdown function is enabled.
DHCP trusted port	Whether to enable the DHCP trusted port function.
Address learning	Whether terminal address learning is enabled on the AP's wired interface.
IP packet binding check	Whether IP packet binding check is enabled on the AP's wired interface.
ARP packet binding check	Whether dynamic ARP inspection (DAI) is enabled on the AP's wired interface.
ACL for inbound packet filtering	ACL for filtering incoming packets. Click . Search for and select an ACL in ACL for inbound packet filtering.
ACL for outbound packet filtering	ACL for filtering outgoing packets. Click . Search for and select an ACL in ACL for outbound packet filtering.
Port PVID	PVID of the wired interface.
Added VLAN ID	ID of the VLAN to which the wired interface is added.
Mode	Mode used to add the wired interface to a VLAN. Tagged and untagged modes are supported.
Packet filtering NOTE: The current version supports only IPv4 packet filtering.
IPv4 ACL	Packet filtering ACL. Click . Search for and select an ACL in ACL List.
Re-marking NOTE: The current version supports only IPv4 packet re-marking.
IPv4 ACL	Packet filtering ACL. Click . Search for and select an ACL in ACL List.
Re-marking Type	Packet re-marking type.
Re-marking Packets	Re-marked packet priority.
Storm Control
Broadcast packet rate limit	Maximum broadcast traffic volume allowed on the AP's wired interface.
Unicast packet rate limit	Maximum unknown unicast traffic volume allowed the AP's wired interface.
Multicast packet rate limit	Maximum multicast traffic volume allowed on the AP's wired interface.

Click Apply. In the Info dialog box that is displayed, click OK.

Modify an AP wired port profile.
1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
2. Click the name of the AP wired port profile that you want to modify. The AP Wired Port Profile page is displayed.
3. Modify parameters of the AP wired port profile. Table 1 describes the parameters for modifying an AP wired port profile.
4. Click Apply. In the Info dialog box that is displayed, click OK.
Delete an AP wired port profile.
1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
2. Select the profile that you want to delete and click Delete. In the Confirm dialog box that is displayed, click OK.
Display the profile reference relationship.
1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
2. Select the profile of which you want to display the reference relationship and click Display Reference Relationship. The system displays the types and names of the objects that reference the profile.
  NOTE:
  Click Hide Reference Relationship. The system hides the displayed results.
Configure the profiles that are referenced by the AP wired port profile.
1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed. Click next to AP Wired Port Profile. The AP wired port profile name is displayed. Click next to the specified AP wired port profile to view the profiles that are referenced by the AP wired port profile.
2. Click any profile referenced by the AP wired port profile. The configuration page of the referenced profile is displayed on the right. You can select another profile from the drop-down list and set the profile parameters. For descriptions of the profile parameters, see its configuration page.
3. Click Apply. In the Info dialog box that is displayed, click OK.