MQC Configuration

Procedure

• Creating a traffic classifier
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Click Create in the Traffic Classifier area. The Creating a Traffic Classifier page is displayed, .

     Table 1 describes the parameters on the page.

     Table 1 Creating a traffic classifier

     Parameter	Description
     Traffic classifier name	Indicates the name of a traffic classifier.
     Relationship between rules	Indicates the logical relationship between rules in a traffic classifier. Or: OR relationship between rules. And: AND relationship between rules.
     Matching rule
     Match packet type	Specifies whether to perform traffic classification based on all data packets or discarded packets. All packets: traffic classification based on all data packets. Dropped packets: traffic classification based on discarded packets.
     Match layer 2 protocols	Indicates a matching rule based on a Layer 2 encapsulated protocol field for traffic classification. - None -: Traffic classification is performed without specifying a Layer 2 encapsulated protocol field. ARP: Traffic classification is performed based on the ARP protocol field. IP: Traffic classification is performed based on the IP protocol field. MPLS: Traffic classification is performed based on the MPLS protocol field. RARP: Traffic classification is performed based on the RARP protocol field.
     Match IP address	Indicates a matching rule based on a protocol for traffic classification. - None -: Traffic classification is performed without specifying a protocol. IPv4: Traffic classification is performed based on the IPv4 protocol. IPv6: Traffic classification is performed based on the IPv6 protocol.
     Match priority
     DSCP	Configures traffic classification based on the DSCP priority of packets.
     IP preference	Configures traffic classification based on the IP preference of packets.
     VLAN 802.1p	Configures traffic classification based on the 802.1p priority of VLAN packets.
     Inner VLAN 802.1p	Configures traffic classification based on the inner 802.1p priority of QinQ packets.
     Match VLAN NOTE: Multiple match VLANs can be configured.
     Start VLAN	Configures the outer start VLAN for traffic classification based on a VLAN ID.
     End VLAN	Configures the outer end VLAN for traffic classification based on a VLAN ID.
     Inner VLAN	Configures the inner VLAN for traffic classification based on a VLAN ID.
     Match MAC address
     Source MAC	Indicates the source MAC address in a traffic classifier.
     Mask	Indicates the mask of the source MAC address in a traffic classifier.
     Destination MAC	Indicates the destination MAC address in a traffic classifier.
     Mask	Indicates the mask of the destination of the MAC address in a traffic classifier.
     Match interface
     Outbound interface	Indicates the outbound interface of packets in a traffic classifier.
     Inbound interface	Indicates the inbound interface of packets in a traffic classifier.
     Match ACL
     ACL IPV4	Indicates the IPv4 ACL in a traffic classifier.
     ACL IPV6	Indicates the IPv6 ACL in a traffic classifier.

  3. Specify the parameters.
  4. Click OK to complete the configuration.
• Modifying a traffic classifier
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Click an entry in the Traffic Classifier area. The page where you can modify the traffic classifier is displayed. Table 1 describes the parameters on the page.

     Traffic classifier name and Relationship between rules cannot be modified.

  3. Modify the parameters.
  4. Click OK to complete the configuration.
• Deleting a traffic classifier
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Select a to-be-deleted entry in the Traffic Classifier area and click Delete. Then a confirmation message is displayed.
  3. Click OK to complete the configuration.
• Refreshing a traffic classifier
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Click Refresh in the Traffic Classifier area.
• Creating a traffic behavior
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Click Create in the Traffic Behavior area. The Creating a Traffic Behavior page is displayed, .

     Table 2 describes the parameters on the page.

     Table 2 Creating a traffic behavior

     Parameter	Description
     Traffic behavior name	Indicates the name of a traffic behavior.
     Traffic action	Indicates a traffic action. - None -: Access control is not performed on service packets based on traffic classification. Permit: Packets that match traffic classification rules are forwarded based on the original policy. Deny: Service flows that match traffic classification rules cannot pass.
     Traffic statistics collection	Enables or disables traffic statistics collection.
     Configuring Traffic Policing
     CIR(kbit/s)	Indicates the committed information rate (CIR).
     PIR(kbit/s)	Indicates the peak information rate (PIR).
     CBS(Byte)	Indicates the committed burst size (CBS).
     PBS(Byte)	Indicates the peak burst size (PBS).
     Green packets Yellow packets Red packets Remarking priority type 802.1p priority DSCP priority	Indicates the traffic policing action to be taken on packets in different colors, the type of priority to be re-marked, and the corresponding priority value.
     Configuring Re-marking
     802.1p priority	Remarks the 802.1p priority of VLAN packets in a traffic behavior.
     Local priority	Remarks the internal priority of packets in a traffic behavior. NOTE: 802.1p priority and Local priority cannot be configured for the same traffic behavior at the same time.
     DSCP priority	Remarks the DSCP priority of IP packets in a traffic behavior.
     IP priority	Remarks the IP precedence of packets in a traffic behavior. NOTE: DSCP priority and IP priority cannot be configured for the same traffic behavior at the same time.
     VLAN ID	Remarks the VLAN ID of VLAN packets in a traffic behavior.
     Inner VLAN	Configures the inner VLAN for traffic classification based on a VLAN ID.
     Flow ID	Configures the flow ID of packets to be re-marked by a traffic behavior. NOTE: Only the S5731-H, S5731-S, S5731S-S, S5731S-H, S5732-H, S2730S-S, S5735-L-I, S5735-L1,S300, S5735-L, S5735S-L, S5735S-L1, S5735S-L-M, S5735-S, S500, S5735-S-I, S5735S-S, S6735-S, S6720-EI, S6720S-EI, S6730-H, S6730S-H, S6730-S, and S6730S-S support this parameter.
     Destination MAC address	Configures the destination MAC address of packets to be re-marked by a traffic behavior. NOTE: Only the S6735-S, S6720-EI and S6720S-EI support this parameter.
     Configuring an Observing Port
     Observing port	Indicates an observing port.
     Configuring Redirection
     Redirection target	Specifies whether to create a packet redirection action in a traffic behavior. - None -: Creates no packet redirection action in a traffic behavior. Interface: Creates an action of redirecting packets to a specified interface in a traffic behavior. Next-hop IPv4 address: Creates an action of redirecting packets to a next-hop IPv4 address in a traffic behavior. Next-hop IPv6 address: Creates an action of redirecting packets to a next-hop IPv6 address in a traffic behavior. CPU: Creates an action of redirecting packets to the CPU in a traffic behavior.
     Target interface	Indicates an interface to which packets are redirected in a traffic behavior.
     Next-hop IPv4 address	Indicates a next-hop IPv4 address to which packets are redirected in a traffic behavior.
     Next-hop IPv6 address	Indicates a next-hop IPv6 address to which packets are redirected in a traffic behavior.
     Forcible redirection	Indicates forcible redirection.

  3. Specify the parameters.
  4. Click OK to complete the configuration.
• Modifying a traffic behavior
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Click an entry in the Traffic Behavior area. The page where you can modify the traffic behavior is displayed. Table 2 describes the parameters on the page.

     Traffic behavior name cannot be modified.

  3. Modify the parameters.
  4. Click OK to complete the configuration.
• Deleting a traffic behavior
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Select a to-be-deleted entry in the Traffic Behavior area and click Delete. Then a confirmation message is displayed.
  3. Click OK to complete the configuration.
• Refreshing a traffic behavior
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Click Refresh in the Traffic Behavior area.
• Creating a traffic policy
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Click Create in the Traffic Policy area. The Creating a Traffic Policy page is displayed, .

     Table 3 describes the parameters on the page.

     Table 3 Creating a traffic policy

     Parameter	Description
     Traffic policy name	Indicates the name of a traffic policy.
     Traffic classifier	Binds a traffic classifier in a traffic policy.
     Traffic behavior	Binds a traffic behavior in a traffic policy.

  3. Specify the parameters.

     Click , and you can bind multiple traffic classifiers and traffic behaviors in a traffic policy.

  4. Click OK to complete the configuration.
• Modifying a traffic policy
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Click an entry in the Traffic Policy area. The page where you can modify the traffic policy is displayed. Table 3 describes the parameters on the page.

     Traffic policy name cannot be modified.

  3. Modify the parameters.
  4. Click OK to complete the configuration.
• Deleting a traffic policy
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Select a to-be-deleted entry in the Traffic Policy area and click Delete. Then a confirmation message is displayed.
  3. Click OK to complete the configuration.
• Refreshing a traffic policy
  1. Choose Configuration > Advanced Services > MQC > MQC Configuration. The configuration page is displayed.
  2. Click Refresh in the Traffic Policy area.