Customized

Context

This section describes how to configure interface parameters to meet service requirements.

Procedure

  1. Choose Configuration > Basic Services > Interface Settings > Service Interface Setting. Click Customized.

  2. Select a port to be configured. Perform the following operations as required in the port area:

    • Click a port icon. To deselect the port, click the port icon again.
    • Drag the cursor to select consecutive ports in a batch.
    • Click multiple port icons to select these ports, and click a port icon again to deselect the port.
    • Select a slot where an LPU is located. All ports on the LPU are selected.

  3. Configure interfaces.

    Table 1 describes parameters and their values.

    Table 1 Customized parameter settings

    Parameter

    Description

    Interface Status

    Set interface status.

    • ON: The current interface is enabled.
    • OFF: The current interface is disabled.

    Work Mode

    Set the working mode for the interface. This parameter is unavailable when Enable link aggregation is selected.

    • Layer two working mode
    • Layer three working mode

    IPv4 Address/Mask

    Configure an IPv4 address and mask for the interface.

    NOTE:

    This parameter is available only when one interface is selected and its working mode is set to Layer three working mode.

    IPv6 address/Prefix Length

    Configure an IPv6 address and prefix length for the interface.

    NOTE:

    This parameter is available only when one interface is selected and its working mode is set to Layer three working mode.

    Load balancing mode

    Set the load balancing mode of an Eth-Trunk. This parameter is available only when Enable link aggregation is selected.

    • dst-ip: Load balancing is performed based on the destination IP address.
    • dst-mac: Load balancing is performed based on the destination MAC address.
    • src-ip: Load balancing is performed based on the source IP address.
    • src-mac: Load balancing is performed based on the source MAC address.
    • src-dst-ip: Load balancing is performed based on the Exclusive-OR calculation result of the source and destination IP addresses.
    • src-dst-mac: Load balancing is performed based on the Exclusive-OR calculation result of the source and destination MAC addresses.

    Eth-Trunk

    Configure the ID of an Eth-Trunk to which an interface is added. This parameter can be set only when Enable link aggregation is selected.

    Eth-Trunk Mode

    Set the Eth-Trunk working mode. This parameter can be set only when Enable link aggregation is selected.

    • Manual load balancing (default): The Eth-Trunk working mode is set to manual.
    • Static LACP: The Eth-Trunk working mode is set to LACP.

    Link Type

    Set the link type of an interface.

    • - None -: The link type of an interface is set to negotiation-desirable.
    • Access: The link type of an interface is set to access.
    • Trunk: The link type of an interface is set to trunk.
    • Hybrid: The link type of an interface is set to hybrid.

    Default VLAN

    Set the default VLAN to which an interface is added. The value is in the range 1 to 4094. This parameter can be set only when Link Type is set to Access, Trunk, or Hybrid.

    Pass VLAN(Tagged)

    Configure frames of the VLAN to pass through the interface in tagged mode. This parameter can be set only when Link Type is set to Trunk or Hybrid.

    Pass VLAN(Untagged)

    Configure frames of the VLAN to pass through the interface in untagged mode. This parameter can be set only when Link Type is set to Hybrid.

    Auto-Negotiation

    Configure auto-negotiation on the interface.

    • ON: Auto-negotiation is enabled.
    • OFF: Auto-negotiation is disabled.

    Interface Rate

    This parameter is available only when Auto-Negotiation is set to OFF.

    Configure the interface rate.

    Duplex Mode

    This parameter is available only when Auto-Negotiation is set to OFF.

    Configure the duplex mode on an interface.
    • Full-duplex
    • Half-duplex

    Jumbo

    Configure the length of jumbo frames. The value in the range 1536 to 12288.

    Combo type

    Configure the working mode of a combo interface.

    • Auto: The combo interface automatically selects the working mode.
    • Copper: The combo interface works as an electrical interface and uses a network cable to transmit and receive data.
    • Fiber: The combo interface works as an optical interface and uses an optical fiber to transmit and receive data.

    Description

    Configure interface description.

    MAC address flapping action

    Configure the action to perform on an interface when MAC address flapping is detected on the interface.

    • - None -: No action is configured.
    • error-down: Shuts down an interface when MAC address flapping is detected on the interface.
    • quit-vlan: Removes an interface from the VLAN where MAC address flapping occurs when MAC address flapping is detected on the interface.

    VLAN/Maximum Number of Dynamic ARP Entries

    Set the maximum number of dynamic ARP entries that an interface can learn from a specified VLAN.

  4. Click Apply for the configuration to take effect.
Parent topic: Interface Settings
Copyright © Huawei Technologies Co., Ltd.