Viewing Alarms on the ISM

Prerequisites

The maintenance terminal must meet the following requirements before an ISM is installed.

• Compatibility with operating systems and browsers
  Table 1 lists the operating systems and browsers supported by the ISM.

  Table 1 Operating systems and browsers that are compatible with ISM

  Operating System	Browser
  Windows Server 2003 Enterprise Edition SP2	Internet Explorer 7.0 Internet Explorer 8.0 Firefox 3.5 and later
  Windows Server 2003 Standard Edition SP2
  Windows Server 2008 Enterprise Edition SP2
  Windows Server 2008 Standard Edition SP2
  Windows XP Professional SP2
  Windows 7
  Red Hat Enterprise Linux AS 5 U3for X86/X86_64	Firefox 3.5 and later
  SUSE Linux Enterprise Server 10 SP2 for X86/X86_64
  Solaris 10 U5 for X86	Firefox 3.5 and later Mozilla 5.0
  Solaris 10 U6 for X86
  Mac OS X 10.6.6 or later	Safari 4.0 NOTE: Safari is a browser built in Mac OS X operating systems and you are not required to install Safari separately.

  NOTE:

  To use an Internet Explorer 6.0 browser, choose Tools > Internet Options > Advanced > Security > Use TLS 1.0 on the browser and then restart the browser.

• Resource Requirement

  The maintenance terminal has a memory not smaller than 512 MB and is configured with a dual-core or quad-core CPU.

• The maintenance terminal communicates with the storage properly.

NOTE:

• The default two management network port IP addresses of the storage system are 192.168.128.101 and 192.168.128.102, and the default subnet mask is 255.255.0.0.
• If the IP addresses of the maintenance terminal and the management port reside in different network segments, configure the initial IP address of the management network port by referring to OceanStor Dorado2100 G2 Storage System V100R001 Installation Guide or OceanStor Dorado5100 Storage System V100R001 Installation Guide.

• You are not advised to open ISM using a 360 browser on any operating system.

Procedure

1. Download the ISM.
   1. Run a web browser on your maintenance terminal.
   2. In the address box of the browser, enter the IP address.

      XXX.XXX.XXX.XXX is the IP address of a controller management network port on the storage device where the ISM is installed. Enter the IP address of the management network port on controller A or controller B to download the ISM software.

   NOTE:

   • When using the IPv6 address of the controller management port on the storage device to download ISM, enter https://[XXXX:XXXX:XXXX:XXXX:XXXX:XXXX:XXXX:XXXX] in the browser.
   • The browser may prompt a message indicating that there is a security certificate issue. Ignore this message and continue the login if the entered IP address is correct.

2. Optional: Load the Java runtime environment (JRE).

   If no applicable JRE version is installed on the maintenance terminal, perform the following steps.

   The applicable JRE version for the ISM software is JRE 1.6.0_20. Obtain the JRE installation driver from the storage system delivery-attached ISM CD-ROM. This section describes how to install the JRE on a Windows operating system.

   1. Run the JRE installation package.

      The Java Installation-Welcome dialog box is displayed.

   2. Click Install.

      The system starts to install the JRE. The installation progress is displayed. After the installation, the Installation Completed dialog box is displayed.

   3. Click Close.

      The JRE is installed.

3. Install the ISM.
   1. On the main interface, click Click Here to Launch OceanStor ISM.
   2. The system starts to load the ISM software.

      When loading is complete, the Select Language dialog box is displayed, as shown in Figure 1.

      Figure 1 Installing the ISM
      
   3. Select a language from the Language drop-down list.

      The ISM user interface is displayed in the selected language.

   4. Click OK or press Enter.

      The ISM welcome page is displayed, as shown in Figure 2.

      Figure 2 Starting the ISM
      

4. Log in to the ISM.
   1. On the menu bar, choose System > Discover Device.

      The Discover Device dialog box is displayed.

   2. Enter User Name and Password of the device and choose Authentication Mode and Device Type, as shown in Figure 3.
      Figure 3 Discovering a Device
      
   3. Method of discovering a device.
      The ISM provides three device discovery modes. Table 2 describes these modes.

      Table 2 Device discovery methods

      Discovery Method	Description
      Specifying an IP address	Searches for a storage device using the specified IP address.
      Specifying an IP address segment	Searches for storage devices based on the specified IP address segment. All storage devices in the specified IP address segment will be discovered.
      Same sub-network	Searches for storage devices in the IP address segment of the maintenance terminal where the ISM is installed. For example, if the IP address and subnet mask of the maintenance terminal where the ISM is installed are 129.16.101.14 and 255.255.0.0, all the storage devices in the 129.16.0.0 network segment will be discovered. NOTE: To delete multiple devices on the navigation tree, stop monitoring of the device. Choose Help > Help Topics to view details.

   4. Click OK.

      The Task Manager dialog box is displayed indicating the process of device discovery.

5. View current alarms.

   In the upper right corner of ISM, click Critical, Major, or Warning. You can view critical and major alarms and warnings. Figure 4 shows how to view major alarms.

   Figure 4 Viewing an Alarm