HSCL05xx logical partition error codes

These error codes can be displayed in a window that is displayed on the HMC screen during system configuration and operations.
Back to HSCL error codes page
HSCL05xx error codes Message Recovery action
HSCL0500 The operation violates the Workload Management Policy. It may be due to one of the following reasons:
  1. Deleting a partition which belongs to a cluster.
  2. Changing a partition cluster ID from one cluster to another cluster.
  3. Running dynamic partitioned move operation between two partitions which belong to the same cluster.
 Check the operation.
  1. For deleting a clustered partition, first move it out of the cluster and then delete it.
  2. For changing a cluster ID, first change it to a non-clustered partition, then change to the destination cluster.
  3. It is not allowed to move processor or memory between two clusters.
HSCL0589 Could not delete partition {0}. Refresh the interface and check whether the operation was performed. If not, try the operation again.
  1. Refresh the interface and check whether the operation was performed.
  2. If not, rebuild the managed system, and try the task again. For details, see Updating managed system or frame information.
  3. If the operation still fails, contact your next level of support or your service provider.
HSCL058A Could not activate the logical partition on logical partition {0} with ID {1}. Refresh the interface and check whether the operation was performed. If not, try the operation again.
  1. Perform a rebuild of the managed system. For details, see Updating managed system or frame information.
  2. Try the task again.
  3. If the operation still fails, contact your next level of support or your service provider.
HSCL058C User defined name cannot be blank or empty.
  1. Set a non-blank user defined name for this partition.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL058D The user defined name cannot be longer than {0} characters.
  1. The partition's user-defined name is too long. Shorten this partition's user-defined name, and try the operation again.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL058F Cannot activate a LPAR when the managed system state is No Power.
  1. Verify that the managed system is in the Operating or Standby state and try the task again.
  2. If the state is not Operating or Standby, refer to Correcting the managed system operating state and perform the appropriate procedure to put the managed system in the correct state.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL059A Cannot activate the logical partition. The profile's maximum memory amount exceeds the managed system's memory limit. Change the profile's maximum memory amount. Change the profile's maximum memory amount, and retry the operation.
HSCL059D This panel function is not enabled at this time.  
HSCL059E Failed to get supported panel functions from firmware.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL05DC The partition does not have Virtual IO Server capability. Choose the correct partition and retry the command.
HSCL05DD Could not get logical partition state. Repeat the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL05DE A logical partition in the managed system already uses the name {0}. Provide another name for this logical partition. Rename the logical partition to a name that is not yet used by other logical partitions in the same managed system. Refer to the logical partition help text for details.
HSCL05DF The logical partition is not in a state under which this operation can be performed. Check the state of the logical partition.
  1. Verify that the operation is allowable under this logical partition state.
  2. Refer to Correcting the managed system operating state and perform the appropriate procedure to put the managed system in the correct state.
HSCL05E0 The logical partition {0} is in an undefined state. Rebuild the managed system.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Restart the HMC.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL05E1 Only {0} logical partitions can be allocated on this managed system can be allocated. There are no more unallocated logical partitions available. Delete unused or unwanted logical partitions for this managed system and retry the operation. Logical partitions in the ready state are currently not in use. Delete unused or unwanted logical partitions. Logical partitions in the ready state are currently not in use. Refer to the logical partition help text for details.
HSCL05E2 Partition is in an unrecognized state.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Try the operation again.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL05E3 Partition is in an unrecognized state.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Try the operation again.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL05E5 Unable to create partition when the managed system is in {0} state. Ensure that the managed system is in the Operating or Standby state .
  1. Verify that the managed system is in the Operating or Standby state.
  2. If it is not in the Operating or Standby state refer to Correcting the managed system operating state and perform the appropriate procedure to put the managed system in the correct state.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL05E6 Logical partition {0} delete failed. Cannot delete a partition when its state is not in the Not Activated state. Perform a shut down operation then delete the partition.
  1. Verify the partition is in Not Activated state.
  2. Perform a Rebuild Managed System operation. For details, see Updating managed system or frame information.
  3. Then try the task again.
HSCL05E7 The profile you tried to activate does not belong to the logical partition {0} you specified. Select the correct LPAR profile. Verify that you selected the correct logical partition profile to activate.
HSCL05E9 Could not activate the logical partition. Ensure that the partition is not already activated and that the managed system is in the Operating or Standby state.
  1. Verify that the logical partition is not already activated, and the state and power-on condition of the managed system are correct, and try the operation again.
  2. If necessary, refer to Correcting the managed system operating state and perform the appropriate procedure to put the managed system in the correct state.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL05EA Cannot activate the partition when it is in state {0}. Ensure the partition is in the Not Activated state.
  1. Verify that the logical partition is not in the running, booting, or open firmware state.
  2. If necessary, refer to Correcting the managed system operating state and perform the appropriate procedure to put the managed system in the correct state.
  3. If it still fails, contact your next level of support or your service provider.
HSCL05EB Could not create the partition. Make sure that all requirements are met for creating a logical partition.
  1. To verify that all the requirements for creating a logical partition are met, refer to Partitioning the server.
  2. If all requirements are met, do a rebuild of the managed system. For details, see Updating managed system or frame information.
  3. Retry the task.
  4. If the problem persists, contact your next level of support or your service provider.
HSCL05EC Could not delete logical partition {0}. Ensure that all requirements are met for deleting a logical partition.
  1. Verify that all the requirements for deleting a logical partition are met.
  2. Perform a rebuild of the managed system. For details, see Updating managed system or frame information.
  3. Retry the task.
  4. If it still fails, contact your next level of support or your service provider.
HSCL05ED Could not set the properties for logical partition {0}. Try again
  1. Repeat the operation.
  2. If the operation still fails, contact your next level of support or your service provider.
HSCL05EE Could not get the managed system's service provider. processor log entry. Try again
  1. Repeat the operation.
  2. If the operation still fails, contact your next level of support or your service provider.
HSCL05EF This new logical partition does not have a user-defined name. Specify a name for the logical partition.
  1. Set the user-defined name for this logical partition. For details, see Viewing information about the managed system.
  2. If it still fails, contact your next level of support or your service provider.
HSCL05F3 Could not display the OS reset dialog for logical partition {0}. Try again.
  1. Refresh the interface and check whether the operation was performed.
  2. If not, rebuild the managed system. For details, see Updating managed system or frame information.
  3. Retry the task.
  4. If the operation still fails, contact your next level of support or your service provider.
HSCL05F4 Could not display the logical partition activate dialog for logical partition {0}. Try again.
  1. Log off and then log in to the HMC and try the operation again.
  2. If this does not correct the problem, contact your next level of support or your service provider.
HSCL05F5 Could not display the create logical partition dialog for the managed system: {0}. Try again.
  1. Log off and then log in to the HMC and try the operation again.
  2. If this does not correct the problem, contact your next level of support or your service provider.
HSCL05F7 Could not open the virtual terminal for logical partition {0} with ID {1}.
  1. Refresh the interface and check whether the operation was performed.
  2. If not, rebuild the managed system, and try the task again. For details, see Updating managed system or frame information.
  3. If the operation still fails, contact your next level of support or your service provider.
HSCL05F8 Could not perform the OS reset {0} reset on logical partition {1} with ID {2}.
  1. Refresh the interface and check whether the operation was performed.
  2. If not, rebuild the managed system, and try the task again. For details, see Updating managed system or frame information.
  3. If the operation still fails, contact your next level of support or your service provider.
HSCL05F9 Could not delete logical partition {0}. Refresh the interface and check whether the operation was performed. If not, try the operation again.
  1. Verify that the logical partition displays on the graphical user interface.
  2. Delete the logical partition again, and check the graphical user interface to see if it is updated appropriately.
  3. Log off and log back in to the HMC.
  4. Contact your next level of support or your service provider.
Parent topic: HMC error codes
Send feedback | Rate this page