HSCL29xx user management error codes

These error codes can be displayed in a window that is displayed on the HMC screen during system configuration and operations.
Back to HSCL error codes page
HSCL29xx error codes Message Recovery action
HSCL2901 This logical partition is not capable of adding, removing, or moving processors dynamically. Ensure your logical partitions are capable of performing dynamic logical partition operations.
HSCL2902 The destination logical partition is not capable of adding, removing, or moving processors dynamically. Ensure your logical partitions are capable of performing dynamic logical partition operations.
HSCL2903 Your processor request goes below the profile's required processor limit. You can remove or move {0} or fewer processors. Retry the operation. Retry the operation, entering a smaller number of processors.
HSCL2904 Your processor request exceeds the profile's maximum processor limit. You can add or move up to {0} processors. Retry the operation. Retry the operation, entering a smaller number of processors.
HSCL2905 This logical partition is not capable of adding, removing, or moving memory dynamically. Ensure your logical partitions are capable of performing dynamic logical partition operations.
HSCL2906 The destination logical partition is not capable of adding, removing, or moving memory dynamically. Ensure your logical partitions are capable of performing dynamic logical partition operations.
HSCL2907 Your memory request exceeds the profile's maximum memory limit. You can add or move up to {0} MBs of memory. Retry the operation.
  1. Retry the task and request a smaller memory amount.
  2. Reset the logical partition, reactivate the logical partition, and then retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2908 Your memory request goes below the profile's minimum memory limit. You can remove or move up to {0} MB of memory. Retry the operation.
  1. Retry the task and request a larger memory amount.
  2. Reset the logical partition, reactivate the logical partition, and then retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2909 Your memory request exceeds the total available memory of the managed system. You can add up to {0} MB of memory. Retry the operation.
  1. Check the available memory of the managed system, retry the task and request a smaller memory amount.
  2. Reset the logical partition, reactivate the logical partition, and then retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL290B This logical partition is not capable of adding, removing, or moving I/O slots dynamically. Ensure your logical partitions are capable of performing dynamic logical partition operations.
HSCL290C The destination logical partition is not capable of adding, removing, or moving I/O slots dynamically. Ensure your logical partitions are capable of performing dynamic logical partition operations.
HSCL2912 The managed system is powered off. You must power on the managed system to perform a dynamic logical partition operation.
  1. Ensure the managed system is powered on.
  2. Rebuild managed system. For details, see Updating managed system or frame information.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2914 The quantity to be added exceeds the available resources.
  1. Ensure that memory is available in the managed system.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2916 The partition could not be found in the database. Perform a rebuild managed system operation, and try again.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2925 An unknown error occurred during the add Virtual adapter operation. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2926 An unknown error occurred during the remove Virtual adapter operation. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2927 Dynamic logical partition MOVE Processing resources failed: {0}.
  1. Retry the task.
  2. Rebuild the managed system. For details, see Updating managed system or frame information.
  3. Retry the task.
  4. If the problem persists, contact your next level of support or your service provider.
HSCL2928 Dynamic logical partition ADD I/O resources failed: {0}.
  1. Ensure you have the resources available to perform the operation.
  2. Retry the operation.
  3. If operation still fails, rebuild the managed system and try the operation again. For details, see Updating managed system or frame information.
  4. If the problem persists, contact your next level of support or your service provider.
HSCL2929 Dynamic logical partition REMOVE I/O resources failed: {0}.
  1. Ensure you have the resources available to perform the operation.
  2. Retry the operation.
  3. If operation still fails, rebuild the managed system and try the operation again. For details, see Updating managed system or frame information.
  4. If the problem persists, contact your next level of support or your service provider.
HSCL2930 Dynamic logical partition MOVE I/O resources failed: {0}.
  1. Ensure you have the resources available to perform the operation.
  2. Retry the operation.
  3. If operation still fails, rebuild the managed system and try the operation again. For details, see Updating managed system or frame information.
  4. If the problem persists, contact your next level of support or your service provider.
HSCL2931 Dynamic logical partition ADD Memory resources failed: {0}.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2932 Dynamic logical partition REMOVE Memory resources failed: {0}.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2933 Dynamic logical partition MOVE Memory resources failed: {0}.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2934 The operating system drmgr command failed. Consult the appropriate operating system log files for further information and retry the operation if desired.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2935 {0} operation for {1} resource did not finish completely in the timeout value specified. The requested number was {2}. The success number is {3}. Increase the timeout value if needed.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2936 {0} operation for {1} resource failed.
  1. Ensure the network connection between the HMC and the logical partition is working.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2937 {0} operation for {1} has completed, but only {3} out of {2} were successful. The partition standard output/error is not available.  
HSCL2938 {0} operation for {1} resource failed. The RPA partition standard output/error is not available.  
HSCL2939 {0} operation for {1} has completed, but only {3} out of {2} were successful. The partition standard output is: {4}. The AIX® standard error is: {5}.  
HSCL293A {0} operation for {1} has completed, but only {3} out of {2} were successful. The partition command is: {4}. The partition standard output is: {5} The partition standard error is: {6}.  
HSCL293B The return code is {0}. The partition return code is {1}.  
HSCL293D Partition {0} is not in the correct state to perform dynamic logical partitioning operations. Dynamic logical partitioning operations can only be performed on running partitions.
  1. Verify that the partition is in the Running state, and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2940 An unknown Dynamic logical partition error has occurred. Try the operation again.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2941 There are no processors available for dynamic logical partitioning on this partition.
  1. Ensure that there are available processors in the managed system.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2942 There is no memory available for dynamic logical partitioning on this partition.
  1. Ensure that there are available processors in the managed system.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2944 The I/O slot cannot be found. Ensure that the correct slot ID and unit ID were entered.
  1. Ensure the inputs are correct.
  2. Rebuild managed system. For details, see Updating managed system or frame information.
  3. Retry the task.
  4. If the problem persists, contact your next level of support or your service provider.
HSCL2945 The shut down operation on the logical partition failed. The return code is {0}.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2946 The logical partition could not be shut down because the HMC's communication to the partition failed. The return code is {0}.
  1. Ensure the network connection between the partition and the HMC is working.
  2. Restart the HMC and retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2947 An error occurred while trying to restore stopped processors. There were {0} processors restored before the error occurred.  
HSCL2949 An error occurred while trying to restore stopped I/O devices. There were {0} devices restored before the error occurred.  
HSCL294A The I/O slot cannot be found or it is required. Ensure that the valid slot ID and unit ID were entered.
  1. Ensure the inputs are correct.
  2. Ensure the adapter is not marked as required.
  3. Rebuild the managed system. For details, see Updating managed system or frame information.
  4. If the problem persists, contact your next level of support or your service provider.
HSCL294C Dynamic logical partition ADD Virtual I/O resources failed: {0}.
  1. Correct the error and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL294D Dynamic logical partition REMOVE Virtual I/O resources failed: {0}.
  1. Correct the error and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL294E Dynamic logical partition ADD Processing resources failed: {0}.
  1. Retry the operation.
  2. If operation still fails, perform a Rebuild Managed System operation, and try the operation again. For details, see Updating managed system or frame information.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL294F Dynamic logical partition REMOVE Processing resources failed: {0}.
  1. Retry the operation.
  2. If operation still fails, perform a Rebuild Managed System operation, and try the operation again. For details, see Updating managed system or frame information.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2950 Dynamic logical partition operation on PCI Host Bridge failed.
  1. Ensure you have the resources available to perform the operation.
  2. Retry the operation.
  3. If operation still fails, perform a Rebuild Managed System operation, and try the operation again. For details, see Updating managed system or frame information.
  4. If the problem persists, contact your next level of support or your service provider.
HSCL2952 The dynamic logical partitioning requested could not be completed due to an unknown error(s) in the local system. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2957 There is currently no RMC connection between the HMC and the RPA partition {0}. This could be because the partition is inactive, a firewall, or an improper network setup causing RMC not to recognize the partition. Please check the system network setup.
  1. Ensure that the network connection is working between HMC and the partition. For details, see Task 4. Ensure that your physical networking is set up correctly.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL2965

DLPAR ADD Processing resources failed. The requested number of processors to be added exceeds the number of processors that are currently available for i5/OS® partitions: {0} processors are currently available.
  1. If there are processors currently available for i5/OS partitions, reduce the requested number of processors to be added to be less than or equal to that number.
  2. Alternatively, shut down other i5/OS partitions or use Dynamic Logical Partitioning to remove processing resources from other i5/OS partitions to release enough processors. Note that the number of i5/OS processors in use by an uncapped i5/OS partition is equivalent to the number of virtual processors in use by that partition. Therefore, in order to release i5/OS processors from an uncapped i5/OS partition, you must release virtual processors from that partition. Releasing one virtual processor from an uncapped i5/OS partition will release one physical i5/OS processor.
  3. Try the task again.
HSCL2966

DLPAR ADD Processing resources failed. The requested number of processing units to be added exceeds the number of processing units that are currently available for i5/OS capped partitions: {0} processing units are currently available.
  1. If there are processing units currently available for i5/OS capped partitions, reduce the requested number of processing units to be added to be less than or equal to that number.
  2. Alternatively, shut down other i5/OS partitions or use Dynamic Logical Partitioning to remove processing resources from other i5/OS partitions to release enough processing units. Note that the number of i5/OS processing units in use by an uncapped i5/OS partition is equivalent to the number of virtual processors in use by that partition. Therefore, in order to release i5/OS processing units from an uncapped i5/OS partition, you must virtual processors from that partition. Releasing one virtual processor from an uncapped i5/OS partition will release one physical i5/OS processing unit.
  3. Try the task again.
HSCL2967

DLPAR ADD Processing resources failed. The requested number of virtual processors to be added exceeds the number of virtual processors that are currently available for i5/OS uncapped partitions: {0} virtual processors are currently available.
  1. If there are virtual processors currently available for i5/OS uncapped partitions, reduce the requested number of virtual processors to be added to be less than or equal to that number.
  2. Alternatively, shut down other i5/OS partitions or use Dynamic Logical Partitioning to remove processing resources from other i5/OS partitions to release enough virtual processors. To add one virtual processor to an uncapped i5/OS partition, one physical i5/OS processor must be available.
  3. Try the task again.
HSCL2968

DLPAR MOVE Processing resources failed. The requested number of processors cannot be moved to the i5/OS partition {0} because doing so would cause the i5/OS processor capacity limit of {1} processors for this managed system to be exceeded.
  1. If possible, reduce the requested number of processors to be moved to the i5/OS partition, and try the task again.
  2. Alternatively, move processing resources from other i5/OS partitions to this partition.
  3. Alternatively, shut down other i5/OS partitions to release i5/OS processors. Note that the number of i5/OS processors in use by an uncapped i5/OS partition is equivalent to the number of virtual processors in use by that partition. Therefore, shutting down an uncapped i5/OS partition will release one physical i5/OS processor for each virtual processor assigned to that partition.
HSCL2969

DLPAR MOVE Processing resources failed. The requested number of processing units cannot be moved to the i5/OS partition {0} because doing so would cause the i5/OS processor capacity limit of {1} processing units for this managed system to be exceeded. Up to {2} processing units can be moved from partition {3} to partition {0}.
  1. If possible, reduce the requested number of processing units to be moved to the i5/OS partition, and try the task again.
  2. Alternatively, move processing resources from other i5/OS partitions to this partition.
  3. Alternatively, shut down other i5/OS partitions to release i5/OS processing units.
    Note: The number of i5/OS processing units in use by an uncapped i5/OS partition is equivalent to the number of virtual processors in use by that partition. Therefore, shutting down an uncapped i5/OS partition will release one physical i5/OS processor.
HSCL296A

DLPAR MOVE Processing resources failed. The requested number of virtual processors cannot be moved to the i5/OS partition {0} because doing so would cause the i5/OS processor capacity limit of {1} processors for this managed system to be exceeded.
  1. If possible, reduce the requested number of virtual processors to be moved to the i5/OS partition, and try the task again.
  2. Alternatively, move processing resources from other i5/OS partitions to this partition.
  3. Alternatively, shut down other i5/OS partitions to release i5/OS virtual processors. To move one virtual processor to an uncapped i5/OS partition, one physical i5/OS processor must be available.
HSCL296B

The i5/OS partition {0} cannot be changed to an uncapped partition because too many virtual processors are assigned to the partition. Reduce the number of virtual processors assigned to the partition and try again.
  1. Make sure that the maximum number of virtual processors defined for the partition is less than or equal to the i5/OS processor capacity limit for your managed system. If it is not, then reduce the maximum number of virtual processors defined in the partition's profile, and then reactivate the partition. Try the task again.
  2. Use Dynamic Logical Partitioning to remove virtual processors from the partition until the total number of processing resources in use by all i5/OS partitions, including the number of virtual processors assigned to this partition, does not exceed the i5/OS processor capacity limit for your managed system. Note that the number of i5/OS processors in use by an uncapped i5/OS partition is equivalent to the number of virtual processors in use by that partition.
  3. Alternatively, shut down other i5/OS partitions or use Dynamic Logical Partitioning to remove processing resources from other i5/OS partitions to release enough virtual processors for this partition.
  4. Try the task again.
HSCL2970 The IOServer command has failed because of the following reason: {0}. Retry the command. If the problem persists, contact your next level of support or your service provider.
HSCL2971 The IOServer command fails because the partition {0} is unknown to RMC/LparCmdRM. This could be because of a firewall or an improper network setup causing RMC not to recognize the partition. Check the system network setup. This could be caused by a firewall or an incorrect network setup causing Resources Monitoring Control (RMC) not to recognize the partition. Check the system network setup.
HSCL2972 There is no active session between the HMC and the partition.
  1. There could be a short interruption in the network causing Resources Monitoring Control (RMC) to not recognize the partition.
  2. Retry the operation later or restart the HMC.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL2973 The IOServer command contained illegal characters such as ; or >. Illegal characters are in the IOServer command. Check the IOServer command to make sure it does not include illegal characters, and try the task again.
HSCL2974 The active profile includes all resources. You are not allowed to add, remove, or move resources from this configuration No recovery action.
HSCL2975 The IOClient command has failed because of the following reason: {0} No recovery action.
HSCL2976 The IOClient command fails because the partition {0} is unknown to RMC/LparCmdRM. This could be because the partition is inactive, or because a firewall or an improper network setup causing RMC not to recognize the partition. Please check the system network setup. Check the system network setup.
HSCL2977 The IOClient command contains illegal characters such as ; or >. No recovery action.
HSCL2978 The partition {0} is not in the Running state. First activate the partition and try the operation again. Activate the partition and try the operation again.
HSCL2979 There was an error retrieving the Virtual IO connection status for the managed system. Execute a rebuild managed system operation. If the error persists contact your service service representative.
  1. Perform a rebuild of the managed system. For details, see Updating managed system or frame information.
  2. Try the task again.
  3. If the operation still fails, contact support.
Parent topic: HMC error codes
Send feedback | Rate this page