SIP3144

• Configuration error, incorrect multipath connection (SRC xxxx4030)
• Configuration error, incomplete multipath connection between adapter and enclosure detected (SRC xxxx4040)

The possible causes are:

• Incorrect cabling to device enclosure.
  Note:
  Pay special attention to the requirement that a Y0-cable, YI-cable, or X-cable must be routed along the right side of the rack frame (as viewed from the rear) when connecting to a disk expansion drawer. Review the device enclosure cabling and correct the cabling as required. To see example device configurations with SAS cabling, see "Serial attached SCSI cable planning," in the Site and Hardware Planning Guide, order number SA76-0091.
• A failed connection caused by a failing component in the SAS fabric between, and including, the adapter and device enclosure.

Considerations:

• Power off the system, partition, or card slot before connecting and disconnecting cables or devices, as appropriate, to prevent hardware damage.
• Some systems have SAS and PCI-X/PCIe bus interface logic integrated onto the system boards and use a pluggable RAID Enablement Card (a non-PCI form factor card) for these SAS/PCI-X/PCIe buses. For these configurations, replacement of the RAID Enablement Card is unlikely to solve a SAS related problem because the SAS interface logic is on the system board.
• Some systems have the disk enclosure or removable media enclosure integrated in the system with no cables. For these configurations the SAS connections are integrated onto the system boards and a failed connection can be the result of a failed system board or integrated device enclosure.
• Some configurations involve a SAS adapter connecting to internal SAS disk enclosures within a system using a cable card. Keep in mind that when the procedure refers to a device enclosure, it could be referring to the internal SAS disk slots or media slots. Also, when the procedure refers to a cable, it could include a cable card.
• When using SAS adapters in a Dual Storage IOA configuration, ensure that the actions taken in this procedure are against the primary adapter (that is, not the secondary adapter).

1. Was the SRC xxxx4030?

   No:

   Go to step 5.

   Yes:

   Go to step 2.

2. Identify the affected adapter and its port by examining the Product Activity Log. Perform the following:
   1. Access SST/DST.
      • If you can enter a command at the console, access system service tools (SST). See System Service Tools (SST).
      • If you cannot enter a command at the console, perform an IPL to DST. See Performing an IPL to DST.
      • If you cannot perform a type A or B IPL, perform a type D IPL from removable media.
   2. Access the Product Activity Log and record address information.

      If a D IPL was NOT performed to get to SST/DST:

      The log information is formatted. Access the Product Activity Log and display the SRC that sent you here. Press the F9 key for "Address Information". This is the adapter address. Then, press F12 to cancel and return to the previous screen. Then press the F4 key to view the "Additional Information" to record the formatted log information. The Adapter Port field indicates the port on the adapter reporting the problem. There may be more than one port listed, since multiple ports map to the same physical connector. For example, ports 0 through 3 map to the first physical connector, 4 through 7 map to the second physical connector, and so on. The port numbers are labelled on the adapter tailstock.

      If a D IPL was performed to get to DST:

      The log information is not formatted. Access the Product Activity Log and display the SRC that sent you here. The direct select address (DSA) of the adapter is in the format BBBB-Cc-bb:

      BBBB

      hexadecimal offsets 4C and 4D

      Cc

      hexadecimal offset 51

      bb

      hexadecimal offset 4F

      In order to interpret the hexadecimal information to get device addresses, see More information from hexadecimal reports. The Adapter Port field indicates the port on the adapter reporting the problem. There may be more than one port listed, since multiple ports map to the same physical connector. For example, ports 0 through 3 map to the first physical connector, 4 through 7 map to the second physical connector, and so on. The port numbers are labelled on the adapter tailstock.

   3. Determine the location of the adapter that reported the problem. See Locating FRUs and find the diagram of the system unit, or the expansion unit. Then find the following:
      • The card slot that is identified by the adapter direct select address (DSA).
      • The physical connector identified by the port number found on the adapter tailstock.
      Have you determined the location of the adapter and its port?
      • No: Ask your next level of support for assistance. This ends the procedure.
      • Yes: Continue with the next step.
3. Review the device enclosure cabling and correct the cabling as required for the device or device enclosure attached to the identified adapter port. To see example device configurations with SAS cabling, see "Serial attached SCSI cable planning," in the Site and Hardware Planning Guide, order number SA76-0091.
4. Perform the following to cause the adapter to rediscover the devices and connections:
   1. Use Hardware Service Manager to re-IPL the virtual I/O processor that is associated with this adapter.
   2. Vary on any other resources attached to the virtual I/O processor.
   Did the error reoccur?

   No:

   This ends the procedure.

   Yes:

   Contact your hardware service provider. This ends the procedure.

5. The SRC is xxxx4040. Determine if a problem still exists for the adapter that logged this error by examining the SAS connections as follows:
   1. On the System Service Tools (SST) screen, select Start a Service Tool then press Enter.
   2. Select Display/Alter/Dump.
   3. Select Display/Alter storage.
   4. Select Licensed Internal Code (LIC) data.
   5. Select Advanced Analysis.
   6. Type in FABQUERY on the entry line and then select it with option 1.
   7. On the Specify Advanced Analysis Options screen, type -SUB 01 -IOA DCxx -DSP 0 in the Options field, where DCxx is the adapter resource name. Press Enter.
      Note:
      More information is available by returning to the Specify Advanced Analysis Options screen and typing -SUB 01 -IOA DCxx -DSP 2 in the Options field, where DCxx is the adapter resource name. Press Enter.
      Do all expected devices appear in the list and are all paths marked as Operational?
      • No: Continue with the next step.
      • Yes: The error condition no longer exists. This ends the procedure.
6. Perform the following to cause the adapter to rediscover the devices and connections:
   1. Use Hardware Service Manager to re-IPL the virtual I/O processor that is associated with this adapter.
   2. Vary on any other resources attached to the virtual I/O processor.
   Note:
   At this point, ignore any problems found and continue with the next step.
7. Determine if the problem still exists for the adapter that logged this error by examining the SAS connections by performing the actions in step 5 again.

   Do all expected devices appear in the list and are all paths marked as Operational?

   NO

   Go to step 8.

   YES

   This ends the procedure.

8. Because the problem persists, some corrective action is needed to resolve the problem. Proceed by doing the following:

   Perform only one of the following corrective actions (listed in the order of preference). If one of the corrective actions has previously been attempted, proceed to the next one in the list.

   • Reseat cables if present on adapter and device enclosure. Perform the following:
     1. Use adapter concurrent maintenance to power off the adapter slot, or power off the system or partition.
     2. Reseat the cables.
     3. Use adapter concurrent maintenance to power on the adapter slot, or power on the system or partition.
   • Replace the cable if present from the adapter to the device enclosure. Perform the following:
     1. Use adapter concurrent maintenance to power off the adapter slot, or power off the system or partition.
     2. Replace the cables.
     3. Use adapter concurrent maintenance to power on the adapter slot, or power on the system or partition.
   • Replace the internal device enclosure or refer to the service documentation for an external expansion drawer. Perform the following:
     1. Power off the system or partition. If the enclosure is external, adapter concurrent maintenance can be used instead to power off the adapter slot.
     2. Replace the device enclosure.
     3. Power on the system or partition. If the enclosure is external, adapter concurrent maintenance can be used instead to power on the adapter slot.
   • Replace the adapter. The procedure to replace the adapter can be found in PCI adapter.
   • Contact your service provider.
9. Determine if the problem still exists for the adapter that logged this error by examining the SAS connections by performing the actions in step 5 again. Do all expected devices appear in the list and are all paths marked as Operational?

   No:

   Go to step 8.

   Yes:

   This ends the procedure.