You might have to replace a SAN Volume Controller 2145-CF8 field-replaceable unit (FRU).
Figure 1 shows how the different parts of the SAN Volume Controller 2145-CF8 are assembled.
- Table 1 calls out the FRUs that are referred to in service procedures.
- Table 2 lists the FRUs that are not referred to by any SAN Volume Controller 2145-CF8 service procedure, but that might be replaced in some circumstances.
- Table 3 lists the FRUs that are related to the optional solid-state drive (SSD) features.
| Assembly index | Part number | Units | Description |
|---|---|---|---|
| -1 | 44T1493 | 6 | Memory module 4 GB memory module, DDR3-1333 2RX4 LP RDIMM |
| -2 | 31P1340 | 1 | Optional: High speed SAS adapter An assembly that includes a high speed SAS adapter card that provides connectivity for up to four solid-state drives (SSDs), a riser card, a blanking plate, and screws. |
| -3 | 33F8354 | 1 | CMOS battery 3.0 volt battery on the system board that maintains power to back up system BIOS settings. |
| -4 | 31P1337 | 1 | 4-port fibre-channel adapter A fibre-channel
host bus adapter (HBA) assembly that connects the SVC CF8 to the fibre-channel
fabric. It is located in PCI slot 1. The adapter assembly includes
the fibre-channel PCI Express adapter, four short-wave SFPs, the riser
card, and the bracket.
Note: If the system is using alternative SFPs,
replace the SFPs on the FRU part with the SFPs from the fibre-channel
adapter that is being replaced.
|
| -5 | 39Y7201 | 2 | Power supply unit Ac power supply, 675 Watt |
| -6 | 44E4372 | 1 | Operator-information panel This assembly includes the information panel that contains the power-control button and diagnostics LEDs. |
| -7 | 42D0673 | 1 | Disk drive The serial-attached SCSI (SAS) 2.5 inch disk drive, which, when ordered as a replacement, might be a supported compatible drive of at least the same capacity as the one being replaced. |
| -8 | 44T2248 | 4 | Drive bay blank EMC filler assembly |
| -9 | 31P1339 | 1 | Service controller The service controller includes the front-panel display, buttons, and associated electronics. |
| -10 | 43V7071 | 1 | Disk backplane Hot-swap SAS 2.5” disk-drive backplane |
| -11 | 43V6929 | 6 | Fan assembly The fan assembly is used in each of the six fan positions. |
| -12 | 43V7072 | 1 | System board The system board is also
called the planar.
Note: This part is the system board
only. When replaced, you must also have alcohol wipes and thermal
grease.
|
| -13 | 44E8690 | 1 | Disk controller SAS controller card for the SAS 2.5 inch disk drive that also includes the riser card. |
| -14 | 44E8690 | 1 | Disk controller / USB riser card Riser card that connects the disk controller to the system board and provides the USB port to which the service controller cable connects. |
| -15 | 46D1266 | 1 | Microprocessor 2.40 GHz Quad-core microprocessor
Note: This
part is the microprocessor only. When replaced, you must also have
alcohol wipes and thermal grease.
|
| - | 31P1338 | 4 | Short-wave SFP Small form-factor pluggable
(SFP) transceiver that provides an auto-negotiating 2, 4, or 8 gigabits-per-second
short-wave optical connection on the 4-port fibre-channel adapter.
Note: It
is possible that SFPs other than those shipped with the product are
in use on the fibre-channel host bus adapter. It is a customer responsibility
to obtain replacement parts for such SFPs. The FRU part number is
shown as "Non standard - supplied by customer" in the vital product
data.
|
| - | 31P1206 | 1 | Service controller cable The USB cable used to connect the service controller to the system board. |
| - | 43V6922 | 1 | Disk signal cable 200 mm SAS disk signal cable |
| - | 46C4148 | 1 | Disk power cable SAS disk power cable |
| - | 31P1294 | 1 | Power cable assembly The cable assembly that connects the SAN Volume Controller and the 2145 UPS-1U. The assembly consists of two power cables bundled with a serial cable. |
| - | 49Y4817 | 1 | Cable-management arm |
| - | 46C4139 | 1 | Operator information panel cable Cable that connects the operator information panel to the system board |
| - | 41Y9292 | - | Thermal grease Grease that helps provide a thermal seal between the processor and the heat sink |
| - | 59P4739 | - | Alcohol wipe Cleaning wipe |
| Description | Part number | Quantity |
|---|---|---|
| Top cover | 43V6933 | 1 |
| Front panel moulding that surrounds the operator information panel | 49Y4818 | 1 |
| Air baffle kit (microprocessor and memory) | 43V6931 | 1 |
| Heat sink | 49Y4820 | 1 |
| Base chassis | 49Y4813 | 1 |
| Rail kit used to install the node in a rack | 49Y4816 | 1 |
| Cable management arm assembly | 49Y4817 | 1 |
| Cable retention bracket | 31P1243 | 1 |
| Front panel USB cable | 43V6920 | 1 |
| Front bezel assembly | 49Y4818 | 1 |
| DVD drive bay filler | 49Y4824 | 1 |
| 240VA safety cover | 49Y4823 | 1 |
| HDD I2C signal cable | 43V7023 | 1 |
| Description | Part number | Quantity | Feature Code |
|---|---|---|---|
| High-speed SAS adapter An assembly that includes a high speed SAS adapter card that provides connectivity for up to four solid-state drive (SSD). The assembly includes a riser card, a blanking plate, and two M3 screws. |
31P1340 | 1 | 4500 |
| High-speed SAS cable This cable connects the high-speed SAS adapter to the disk backplane. |
41Y3884 | 1 | |
| 146 GB Solid-state drive (SSD) | 31P1342 | 1 to 4 | 4601 |
| Description | Part number | Quantity | Feature Code |
|---|---|---|---|
| Long-wave SFP FRU Long-wave SFP transceiver that provides
an auto-negotiating 2, 4, or 8 gigabits-per-second 10 kilometer (km)
long-wave optical connection on the 4-port fibre-channel adapter.
Note: It
is possible that SFPs other than those shipped with the product are
in use on the fibre-channel host bus adapter. It is a customer responsibility
to obtain replacement parts for such SFPs. The FRU part number is
shown as "Non standard - supplied by customer" in the vital product
data.
|
31P1345 | 1 to 4 | 5608 |