Operating the HP ScanJet IIC/P with Windows NT

MORE INFORMATION

The following operational notes discuss each of the essential elements for correct operation of the HP ScanJet IIc. Troubleshooting tips and hints for more effective operation of the HP ScanJet IIc with Windows NT version 3.1 follow the operational notes.

Operational Notes:

1. The scanner needs to be connected to the SCSI Host Adapter in the computer, turned on, and unlocked before you start the computer. Otherwise, the computer will not recognize the scanner. Unlike some versions of the Windows NT Beta, the scanner does not have to be installed, unlocked, and turned on when installing the released version of Windows NT.
2. Edit the CONFIG.NT file so that it contains a line which loads the HPSCAN16.SYS driver. Use a text editor, such as Notepad, to add the following line to the CONFIG.NT file:
   

   DEVICE=%SYSTEMROOT%\SYSTEM32\DRIVERS\HPSCAN16.SYS

   
   The CONFIG.NT file can be found in the SYSTEM32 subdirectory. Setup copies the files HPSCAN16.SYS, HPSCAN32.DLL, and SCSISCAN.SYS to the hard disk when you install Windows NT.
3. The Hewlett-Packard provided in-line terminator must be connected to the 25-pin Macintosh SCSI-out port. The scanner may not be recognized by the system or the DeskScan II software may fail to work if the SCSI bus is incorrectly terminated. Usually, a SCSI bus is terminated at both ends, but not in the middle. Therefore, if the scanner is the last device on the bus, the end of the bus will be at the 25-pin Macintosh SCSI-out port. Do not place an in-line terminator at the 50-pin SCSI-in connection. The scanner may not work properly if the HP provided terminator is replaced with a terminated cable or other SCSI device connected to the 25-pin SCSI- out port.
4. Microsoft has tested all of the SCSI Host Adapters listed in the Windows NT version 3.1 Hardware Compatibility List (HCL) with the HP ScanJet IIc. However, as stated in the HCL, not all of the SCSI Host Adapters listed will work correctly with the HP ScanJet IIc. The following SCSI Host Adapters on the HCL will not work correctly with the HP ScanJet IIc:
   
   

         Maynard 16-bit SCSI Adapter  (ISA)
         Data Technology Corp. 3292   (EISA Adapter)
         Olivetti ESC-1               (EISA Adapter)
   						

   
   
   The Maynard 16-bit and DTC 3292 SCSI Adapters are appropriately footnoted in the HCL as not working with scanners, but the HCL documentation does not mention that the Olivetti ESC-1 adapter will not work with the HP ScanJet IIc.
5. The HP ScanJet IIc is very sensitive to incorrect cabling. In order for the scanner to work, the cables must be of high quality and meet the SCSI I or SCSI II specification where appropriate (SCSI II Host Adapters require SCSI II cabling). You must ensure that all connections are firm, with all connector pins in solid contact. Shorter cables have a greater chance of success than longer cables. Be certain that the cables are in very good condition.
6. Use the most current version of the HP DeskScan II software. Presently, the most current version is 1.62. Versions earlier than 1.61 may not function properly under Windows NT.
7. Do not attempt to use the proprietary HP-provided scanner interface card with Windows NT. The supported SCSI Host Adapter takes the place of this card. However, HP has developed a driver that allows you to use the scanner with a SCSI adapter in the MS-DOS and Windows 3.0 or 3.1 environments. The name of this driver is SJIIIx.SYS and it is available by calling HP or from the HP forum on CompuServe.

Troubleshooting Hints and Tips:

If the scanner does not function or you get error messages from the DeskScan II software advising you that the scanner cannot be found, then try the following steps:

WARNING: Using Registry Editor incorrectly can cause serious, system- wide problems that may require you to reinstall Windows NT to correct them. Microsoft cannot guarantee that any problems resulting from the use of Registry Editor can be solved. Use this tool at your own risk.

1. To check if Windows NT has recognized the scanner hardware, start the Registry Editor (REGEDT32.EXE) and choose the HKEY_LOCAL_MACHINE key. Select the following subkey
   

   \HARDWARE\DEVICEMAP\Scsi\Scsi Port 0\Scsi Bus 0\Target Idx \logical Unit Id 0

   
   where x represents the SCSI ID number for the scanning device. Examine the entry at the SCSI ID number of the scanner. This entry should have a value of HP C1750 A.
2. In the Control Panel window, choose Devices to see if the 32-bit driver SCSISCAN.SYS was started. If it has not started, attempt to start it by choosing the Start button. Do not attempt to change the method by which it starts by using the Startup button. The default setting in the Startup dialog box is System. If you try to change this setting to Boot or some other setting, you may lock your Windows NT installation. If this happens, you will have to disconnect the scanner, start MS-DOS, and disable HPSCAN16.SYS in the CONFIG.NT before returning to Windows NT.
3. If HPSCAN16.SYS is loaded as a device driver in the CONFIG.NT file, but you do not have the HP ScanJet IIc connected to the SCSI Host Adapter, then your Windows NT will hang when started. The computer will need to be restarted. To recover, either turn the machine off and reconnect the scanner, or use the "dual boot" functionality of Windows NT by starting the MS-DOS environment and editing the CONFIG.NT to disable the HPSCAN16.SYS device line.
4. The DeskScan II software installation program will create a group called Scanner in the Program Manager. In this group, you will see an icon of a scanner with the icon title of DeskScan II. You may also see icons titled Scanner Test and SCSI Addresses, however, these two applications are not compatible with Windows NT. No resolution or workaround to this problem exists at this time.
5. Be sure that the SCSI ID number set for the scanner does not conflict with the SCSI ID number for any other device on the SCSI bus. SCSI addresses 0 through 7 are displayed on a small, circular SCSI address indicator located between the 50-pin SCSI-in and the 25-pin Macintosh SCSI-out ports at the back of the scanner. In the middle of the indicator dial is a small, narrow slot which can be turned with a tiny flat-bladed screwdriver. Once you change the SCSI ID to a non-conflicting SCSI address, the new SCSI ID will be recognized at system startup and will be written into the Windows NT Registry.
6. To determine whether the HP ScanJet is locked or unlocked, look for a rectangular opening at the back of the scanner just above the 50-pin SCSI port. If there is a half-height black plastic block in the opening, then the scanner is unlocked. To lock the scanner, you must press down firmly on the plastic block. When the block is in the depressed position, a black bar will appear in the rectangular opening. To unlock the scanner, push the horizontal black bar back up to the top of the rectangular opening.

The central technical support number for Hewlett-Packard (HP) is (208) 323-2551.



The Hewlett-Packard products included here are manufactured by a vendor independent of Microsoft; we make no warranty, implied or otherwise, regarding these products' performance or reliability.