Installing and Using the Debugging Version of Windows

Q118891

The information in this article applies to:

SUMMARY

The debugging version of Windows replaces the core Windows code with code that provides additional error checking and reporting not in the standard (non-debugging) version of Windows. This information is useful if you are a developer testing your own application under Windows. The debugging version of Windows will point you to resource leaks and errors that go otherwise undetected; therefore, it is a good idea to run your application under the debugging version at least once, even if the program appears to run without any problems.

You can install the debugging version of Windows from either the Windows SDK or the Visual C++ Professional Edition. General installation and use guidelines are available in the SDK manual "Getting Started" and the Visual C++ manual "Professional Tools User's Guides." This article provides additional information on these subjects.


MORE INFORMATION

First, follow the guidelines in your manual to install the debugging version of Windows. If you have already installed the SDK or Visual C++ and did not choose to install the debugging version, run the setup program again. You only have to install the debugging version at this point. The debugging version is called the "debug kernel." The term "kernel" refers to the operating system core. In Windows, the kernel consists of the GDI.EXE, KRNL386.EXE, and USER.EXE files.

The files that ship with the Windows version 3.1 SDK or Visual C++ work with both Windows version 3.1 and Windows for Workgroups (WFW) version 3.11. The .SYM files are specific to the version of Windows that you are running. If you install from Visual C++ version 1.5 and are using WFW, after installing you need to copy the GDI.SYM, KRNL386.SYM, and USER.SYM files from the CDs MSVC\NODEBUG\WFW311 directory to your MSVC\NODEBUG directory, overwriting the Windows version 3.1 files that are currently in that directory. However, if you are installing from the SDK or Visual C++ version 1.0, you need to copy those three files from your system directory before you run the debugging version of Windows. If you happen to use the wrong .SYM files when not in debugging mode, Windows will still run OK. However, programs like Dr. Watson that use .SYM files will occasionally have output that is off by a couple of bytes. If you need the Windows for Workgroups files, they are available from the Microsoft Software Library in the file DBG311.ZIP. (Make sure to use the -d flag when using PKUNZIP to tell it to maintain the directory structure.)

Once the debugging version is installed, you will have the following batch files available to switch between the non-debugging and the debugging version of Windows: N2D.BAT and D2N.BAT. By default, they are in either the WINDEV\BIN or the MSVC\BIN directory. You will probably want to switch to the non-debugging version when you do not need the extra diagnostics of the debugging version, because the debugging version runs significantly slower due to the increased error checking. When you run the debugging version of Windows, you will see the phrase "Enhanced Mode Debug Windows" in the lower right-hand corner of your screen.

If you start the debugging version of Windows and the error "Cannot write to device AUX" displays, most likely COM1 is not available and you should direct the debugging output elsewhere. For additional information, please see the following article in the Microsoft Knowledge Base:

Q86263 Redirecting Debugging Information Under Windows
You can control the level of diagnostic information by using the debugging version of Windows. The groups of output options are break options, debug options, and trace options. The debug option "break with INT 3" is useful if you are running your program under the debugger: when the program causes a general-protection (GP) fault, the debugger stops on the line of code where the fault occurred. In general, it is a good idea to check all of the trace options and also clear the "Print on Break Only" check box so that printing occurs synchronously. For more information on the debugging version of Windows and the debugging options, see the DBWIN.TXT file that is included with the DBWIN sample and the "Windows Debugging Version/Debugging Programs" topic in the SDK help file.

You can use OutputDebugString() or DebugOutput() in your own application to print debugging output. These APIs are easier to use than MessageBox().

When you run the debugging version of Windows, you may notice errors from other Windows-based applications that you are running. Other applications can even cause general protection faults or machine hangs when they are run under the debugging version. This is a sign that the application developer did not test the application under the debugging version of Windows. If you have an application in your startup group that prevents the debugging version of Windows from loading, hold down the Shift key while booting so that the applications in your startup group are not started.

Additional query words: 3.10

Keywords : kb16bitonly
Issue type :
Technology : kbAudDeveloper kbWin3xSearch kbSDKSearch kbWinSDKSearch kbWinSDK310


Last Reviewed: November 4, 1999
© 2001 Microsoft Corporation. All rights reserved. Terms of Use.