Knowledge Base

TN3270 Server Rejects First Data RU After Host's CLEAR Message

Article ID: 140826

Article Last Modified on 10/22/2003

APPLIES TO

This article was previously published under Q140826

SYMPTOMS

A host application, such as TeleView, allows a user at a terminal to make a connection and then spawn additional sessions on the SNA host. Under normal conditions, the user may terminate a session with no further incident. In this case, however, when a user ends even just one session, the rest of the sessions are terminated. This condition may occur when running the TN3270 Service for Windows NT. The TN3270 Server may also generate the following error:
sense data = 081B0000
The IBM Systems Network Architecture (SNA) Formats guide provides the following information regarding this error:

081B0000
Receiver in Transmit Mode:
A race condition exists: a normal-flow request was received while the
half-duplex contention state was NOT-RECEIVED, or while resources (such
as buffers) necessary for handling normal-flow data were unavailable.

Contrary to the explanation given in the IBM SNA Formats guide, a race condition does not exist in this case. The error is exhibited in the following diagnostic tools:

From the Application Log: 
   Event ID: 309
   INIT failed with LUA_COMM_SUBSYSTEM_NOT_LOADED / LUA_SEC_RC_OK for
   <IP_address> (port <port_number>).

   Event ID: 603
   TN3270 session with client at <IP_address> (port <port_number>) using LU
   <LU_name> terminated abnormally because:
      TN3270 Service Error 505
      SNA API verb INIT failed.
         Failure described as:
         SNA Server has not been started.

   Event ID: 698
   Invalid Destination L-value. Parameter: 0, Message: 0, Valid range
                                                                    <range>

   Event ID: 699
   Invalid message: MsgType 31, MhType 31

   Event  ID: 1955
   RUI_INIT failed for LU, primary_rc=4f0, secondary_rc=0
From an SNA Server API Trace: 
   ...
   ... RUI    ---------------------------------------------- 13:50:43.15
   ... RUI    RUI_READ request
   ...
   ... RUI    ---------------------------------------------- 13:50:43.56
   ... RUI    RUI_READ response
   ... RUI    OK - OK
   ...
   ... RUI    ---------------------------------------------- 13:50:43.57
   ... RUI    RUI_WRITE request
   ...
   ... RUI    ---- Data at address 00119CC4 ----
   ... RUI    081B0000                                <....            >
   ... RUI    ---------------------------------------------- 13:50:43.65
   ... RUI    RUI_WRITE response
   ... RUI    OK - OK
   ...
   ... RUI    ---- Data at address 00119CC4 ----
   ... RUI    081B0000                                <....            >
   ...
From a TN3270 Server Trace: 
   ...
   >11/27 13:50:43.062 (+ smidgen )  Event=TEV_DataToSNA
    Thread = 0x000000C3  Session = 0x0026B7D0  Socket = 0x0000017C
    VCB address=0x0026B9D8
    verb_length=0x0044  verb=0x0052 (RUI)  opcode=0x8004 (WRITE)
    sid=0x00010006  correlator=0x0026B7D0  post_handle=0x00000198
    prim_rc=LUA_OK  sec_rc=LUA_SEC_RC_OK
    lu_norm    lua_data_length=0x00000004
    TH Only    efi=0  oadi=0  daf=FD  oaf=01  snf=0001
    RH -RSP FMD fi=0   sdi=0  bci=1  eci=1  (Only)
    83 91 80    dr1=1  dr2=0  ri=1   qri=0  pi=1
                bbi=1  ebi=0  cdi=0  csi=0  edi=0  pdi=0
    000000  081b0000                             *....            *
   ...
   >11/27 13:50:43.562 (+ smidgen )  Event=TEV_DataToSNA
    Thread = 0x000000C3  Session = 0x0026B7D0  Socket = 0x0000017C
    VCB address=0x0026B9D8
    verb_length=0x0044  verb=0x0052 (RUI)  opcode=0x8004 (WRITE)
    sid=0x00010006  correlator=0x0026B7D0  post_handle=0x00000198
    prim_rc=LUA_OK  sec_rc=LUA_SEC_RC_OK
    lu_norm    lua_data_length=0x00000004
    TH Only    efi=0  oadi=0  daf=FD  oaf=01  snf=0002
    RH -RSP FMD fi=0   sdi=1  bci=1  eci=1  (Only)
    87 91 20    dr1=1  dr2=0  ri=1   qri=0  pi=1
                bbi=0  ebi=0  cdi=1  csi=0  edi=0  pdi=0
    000000  081b0000                             *....            *
   ...

CAUSE

After receiving a CLEAR message from the SNA host, the TN3270 Server may reject the first data response unit (RU) from the SNA host. There are two issues here, both of which have now been fixed:
  1. When the TN3270 Server receives a CLEAR message from the SNA host, it does not reset its internal state which keeps track of whether the TN3270 emulator or the host application has permission to send. This causes the TN3270 Server to reject the first data message received from the SNA host with a sense data = 081B0000, because the TN3270 Server assumes that the TN3270 emulator still has the permission to send. The TN3270 Server then rejects the next data message from the host. At this point, the host application gives up and terminates the session.
  2. When the node receives data from the host application which it believes to be out of bracket it passes a message up to a Request Unit Interface (RUI) application with the Sense Data Included Indicator (sdi) bit set. On receiving this, the RUI application is supposed to send a negative response with the sense data which the node passed up to it. The TN3270 Server, however, was not checking for this bit.

RESOLUTION

Microsoft has updated the files, TN3NTMSG.DLL and TN3SERVR.EXE, to correct this problem.

STATUS

Microsoft has confirmed this to be a problem in SNA Server for Windows NT. This problem was corrected in the latest SNA Server for Windows NT, 2.11 U.S. Service Pack. For information on obtaining the Service Pack, query on the following word in the Microsoft Knowledge Base (without the spaces):

S E R V P A C K


Additional query words: prodsna

Keywords: kbbug kbfix KB140826


Send feedback to Microsoft

© Microsoft Corporation. All rights reserved.