1 INFO-VAX	Sun, 14 May 2000	Volume 2000 : Issue 268       Contents: Re: How Do I Enable Mail?  Re: MONITOR on VMS 7.2  F ----------------------------------------------------------------------  % Date: Sat, 13 May 2000 12:14:21 -0700 5 From: "cstranslations" <cstranslations@email.msn.com> " Subject: Re: How Do I Enable Mail?) Message-ID: <u7F9U$Qv$GA.321@cpmsnbbsa04>   H Is the "dismail" flag set (for the accounts you are using) in authorize?  J That's the first thing that comes to mind. Haven't tried setting it to seeI what happens (and I'm running 7.1 here so it might be something different H from 6.2 anyway). I seem to remember back under 5.5-2 that even with theL flag set you could send mail however if you tried sending mail to an accountK (with the dismail flag set) it would tell you that the user you were trying 3 to send mail to was not authorized to receive mail.   J Took a (very) quick look through the manuals and didn't see anything otherK that the dismail and disnewmail flags that jumped out in an obvious way . .  .    Joe     5 Stephen Henry <stephen@laughnet.net> wrote in message & news:391CDAA5.4D669304@laughnet.net... > C >     I recently purchased a VAX 4000/200 running OpenVMS 6.1 at an H > auction.  I have the system up and running and I'm having a lot of funE > with it, but I can't get into mail.  Every time I try and run it it J > tells me MAIL HAS BEEN DISABLED.  Any ideas as to how to fix this.  I do > have SYSTEM access.  >  >  > Steve  >  > --I > **NEW** Check Out LaughNet After Dark http://www.laughnet.net/afterdark > > Lose Weight Laughing At LaughNet!!   http://www.laughnet.net? > Independent Cartoonist's Homepage http://www.laughnet.net/ich    ------------------------------  # Date: Sat, 13 May 2000 23:36:44 GMT . From: "Shrini Arole" <Someone@somewhere.where> Subject: Re: MONITOR on VMS 7.2 8 Message-ID: <gGlT4.5426$45.60731@news1.rdc1.tn.home.com>  4 No -- no special startup mode - just a regular boot.  A I search all the .COM files in sys$startup for XTI and there is a I VPM$STARTUP.COM, but it does not install the XTILIB image. I could find a & reference to this image anywhere else.   Shrini Arole   shrini@home.com   I "Jean-Franois Marchal" <jean-francois.marchal@x9000.fr> wrote in message - news:8fjmtp$209c$1@s2.feed.news.oleane.net... ) > Did you use some special startup mode ?  > Jean-Franois Marchal 
 > X9000- LYON  > @ > "Someone Somewhere" <Someone@somewhere.where> wrote in message4 > news:iqcT4.5178$45.52580@news1.rdc1.tn.home.com...I > > I am getting the following message when trying to run MONITOR after a  new K > > install of VMS v7.2. If I manually install the image using INSTALL ADD,  I   > > can run the monitor utility.K > > Did I miss something during system setup, or can I just add the install 1 > > command to systartup_vms and be done with it?  > > 2 > > Any help you can provide would be appreciated. > >  > >         Shrini Arole > >         shrini@home.com  > > 6 > > %DCL-W-ACTIMAGE, error activating image XTI$XTILIB > > -CLI-E-IMGNAME, image file9 > > TMMVXD$DKA0:[SYS0.SYSCOMMON.][SYSLIB]XTI$XTILIB.EXE;1 D > > -SYSTEM-F-PRIVINSTALL, shareable images must be installed to run > privileged	 > > image  > > $  > >  > >  > >  > >  >  >  >  >    ------------------------------   End of INFO-VAX 2000.268 ************************