Contents

1   Introduction

This document describes how to enable and configure IPv6 for the MTAS towards its peer nodes.

1.1   Prerequisites

It is assumed that the user of this document is familiar with the O&M area, in general.

1.1.1   Licenses

No licenses are needed.

1.1.2   Documents

Before starting any procedure in this document, ensure that the following documents are available:

• Ericsson Command-Line Interface User Guide
• Managed Object Model (MOM)
• Signaling Manager User Guide

1.1.3   Conditions

The following conditions must apply:

• An Ericsson Command-Line Interface (ECLI) session in Exec mode is in progress.
• The Signaling Manager is connected.

2   Overview

The MTAS can be configured to use either IPv4 or IPv6 for the interfaces supporting IPv6. The external Media Resource Function Controller (MRFC) must use the same IP version as supported by the interfaces to the Serving CSCF (S-CSCF) and Interrogating CSCF (I-CSCF) (IPv6). External MRFC uses SIP and therefore supports IPv6.

The MTAS can use either IPv4 or IPv6 for the H.248 messages on the Mp interface, depending on the capabilities of the MRFC. This also applies towards the Media Resource Function Processor (MRFP), depending on its capabilities.

More interfaces supporting the IPv6 are shown in Figure 1.

IPv4 and IPv6 cannot be used in parallel on the same "logical" interface by the MTAS. It is possible to configure both IPv6 and IPv4 on the same physical interfaces, for more information, refer to MTAS SW Installation.

It is recommended to configure the MTAS with IPv6 after the CSCF and HSS have been configured with IPv6. It is also recommended to remove the A Resource Record in Domain Name System (DNS) server for the MTAS that is connected to the DNS SRV Resource Record used for the MTAS on the ISC interface.

The external interfaces used by the MTAS and weather they support either IPv4 or IPv6, or both, are shown in Figure 1.

2.1   Traffic Impact

Implementing IPv6 on the MTAS has some impact on the traffic, since the MTAS must be deactivated before it can be configured. Therefore, the traffic must be moved to the secondary MTAS before starting to implement IPv6 on the primary MTAS.

When the implementation is finished, the primary MTAS must be activated before moving back the traffic from the secondary MTAS. After that the user can implement IPv6 on the secondary MTAS.

3   IPv6 Configuration

IPv6 configuration includes the following main activities:

• Adding Diameter IPv6 addresses
• MTAS Configuration

The IP configuration attributes are shown in Table 1.

3.1   VIP IPv6 Addresses Configuration in the System

This section describes how to configure VIP IPv6 addresses in the system.

3.1.1   Add VIP IPv6 Address to the System

To add a VIP IPv6 address to the system, see Virtual IP Address Management.

3.1.2   Backup after Adding VIP Address

To create a backup, see Create Backup and System Backup and Restore.

3.1.3   Health Check

After adding a VIP address, ensure that the MTAS is operational by performing a health check, see MTAS Health Check.

3.2   Deactivate MTAS

Before IPv6 configuration is performed, the MTAS must be deactivated.

To deactivate MTAS before IPv6 implementation:

1. Move the traffic to the secondary MTAS.
2. Deactivate the MTAS, see Section Deactivating MTAS in MTAS VNF Management Guide.

   Note:  

   It is recommended to deactivate the MTAS gracefully.

   
   

3.3   Add Provisioning IPv6 Addresses

This section describes how to add and connect Provisioning IPv6 addresses.

3.3.1   Add CAI3G IPv6 Addresses

This section describes how to add CAI3G IPv6 addresses.

3.3.1.1   Update cluster.conf and Reboot the Cluster

1. Log on to SC-1:

   ssh <maintenance_user>@<OAM VIP>

2. Edit the /cluster/etc/cluster.conf file and add the following lines to the SITE SPECIFIC AND SOLUTION INTEGRATION PARAMETERS section (above the tag Other settings for instance). Replace the tags in "<>" with the correct IP addresses:

   host all <cai3g-vip6> cai3g-vip6

3. Save the file and exit the editor.
4. Reload cluster.conf by executing the following command:

   SC-1:~ # cluster config -r

5. Reload the cluster by executing the following command:

   SC-1:~ # cluster reboot -a

3.3.2   Add Ut IPv6 Addresses

This section describes how to add Ut IPv6 addresses.

3.3.2.1   Update cluster.conf and Reboot the Cluster

1. Log on to SC-1:

   ssh <maintenance_user>@<OAM VIP>

2. Edit the /cluster/etc/cluster.conf file and add the following lines to the SITE SPECIFIC AND SOLUTION INTEGRATION PARAMETERS section (above the tag Other settings for instance). Replace the tags in "<>" with the correct IP addresses:

   host all <ut-vip6> ut-vip6

3. Save the file and exit the editor.
4. Reload cluster.conf by executing the following command:

   SC-1:~ # cluster config -r

5. Reload the cluster by executing the following command:

   SC-1:~ # cluster reboot -a

3.4   Add Diameter IPv6 Address

This section describes how to add and connect Diameter IPv6 addresses.

3.4.1   Add CAI3G IPv6 Addresses

This section describes how to add CAI3G IPv6 addresses.

3.4.1.1   Update cluster.conf and Reboot the Cluster

1. Log on to SC-1:

   ssh <maintenance_user>@<OAM VIP>

2. Edit the /cluster/etc/cluster.conf file and add the following lines to the SITE SPECIFIC AND SOLUTION INTEGRATION PARAMETERS section (above the tag Other settings for instance). Replace the tags in "<>" with the correct IP addresses:

   host all <cai3g-vip6> cai3g-vip6

3. Save the file and exit the editor.
4. Reload cluster.conf by executing the following command:

   SC-1:~ # cluster config -r

5. Reload the cluster by executing the following command:

   SC-1:~ # cluster reboot -a

3.4.2   Add Ut IPv6 Addresses

This section describes how to add Ut IPv6 addresses.

3.4.2.1   Update cluster.conf and Reboot the Cluster

1. Log on to SC-1:

   ssh <maintenance_user>@<OAM VIP>

2. Edit the /cluster/etc/cluster.conf file and add the following lines to the SITE SPECIFIC AND SOLUTION INTEGRATION PARAMETERS section (above the tag Other settings for instance). Replace the tags in "<>" with the correct IP addresses:

   host all <ut-vip6> ut-vip6

3. Save the file and exit the editor.
4. Reload cluster.conf by executing the following command:

   SC-1:~ # cluster config -r

5. Reload the cluster by executing the following command:

   SC-1:~ # cluster reboot -a

3.4.3   Disable Own Node

Disable the own node, see Diameter, Configure Own Node.

3.4.4   Add IPv6 to Own Node

Add IPv6 to the own node for Diameter, see Diameter, Configure Own Node.

An example of the input when adding IPv6 to the own node for Diameter is shown in Example 1.

objectClass: DIA-CFG-NeighbourNode
ipAddressesList: 0:2001:1B70:4292:0251::71

3.4.5   Add IPv6 to Peer Node

Add IPv6 to the peer node for Diameter, refer to Diameter, Configure Peer Node and Connections.

An example of how to add IPv6 to the peer node is shown in Example 2.

objectClass: DIA-CFG-NeighbourNode
ipAddressesList: 0:2001:1B70:4292:0251::73

3.4.6   Enable Own Node

Enable the own node, see Diameter, Configure Own Node.

3.4.7   Create New Peer Node Connection with IPv6

Create a peer node connection with IPv6, see Diameter, Configure Peer Node and Connections.

An example on how to create a peer node connection with IPv6 is shown in Example 3.

objectClass: DIA-CFG-Conn
ipAddressesList: 0:2001:1B70:4292:0251::73

When the IPv6 connections are made, the existing IPv4 connections can be deleted if necessary.

3.4.8   Create Backup after MTAS Configuration

Create a backup, see Create Backup and System Backup and Restore.

3.5   MTAS Configuration

This section describes the configuration of the MTAS interfaces towards peer nodes and how to change these nodes to IPv6.

Note:  

To be able to configure the peer nodes, the MTAS must be deactivated. Before the MTAS is activated, the peer nodes must be configured with IPv6 on the affected interfaces.

For more information about the MTAS IP-specific attributes, see Managed Object Model (MOM).

3.5.1   SIP Configuration

The mtasSipIpVersion configures the MTAS to use IPv6 for SIP for the interfaces ISC, Ma, Mr, and Pw. This attribute must be set to 1 since only one IP version (IPv6 only) can be used.

Check that the mtasSipIcscfName attribute is an FGDN.

Change to IPv6 for SIP, see Section Changing IP-version in MTAS SIP Management Guide.

3.5.2   H.248 Configuration

The mtasMpControllerIpVersion attribute defines what type of IP protocol the MTAS uses for H.248 messages on the Mp interface towards the MRFP. Whether MTAS supports IPv6 or IPv4 towards the MRFP, depend on the capabilities of the MRFC.

The External MRFC uses SIP and can therefore handle IPv6.

To change the IP protocol version for the MRFC, see MTAS Media Control Management Guide.

3.5.3   Parlay X Configuration

The mtasParlayXIpVersion attribute defines what type of IP protocol the MTAS uses on both the Parlay X interface and the Cr interface. If peers of these interfaces use IPv6, this attribute must be changed for IPv6. The Cr interface is used together with Mr interface for External MRFC deployment.

To change the value of the attribute, see MTAS Parlay X Management Guide.

3.5.4   NameDB Configuration

The MtasIdPres.mtasIdPresDbIpVersion attribute defines the type of IP protocol the MTAS uses for sending and receiving SOAP messages on the NameDb interface to a Calling Name Server. If the Calling Name Server uses IPv6, this attribute must be changed for IPv6.

To change the IP protocol version of the Calling Name Server, see MTAS Calling Name Identity Presentation Management Guide.

3.5.5   DNS Configuration

The MTAS can use either IPv4 or IPv6 to communicate with the DNS. The IPv6 addresses for the DNS servers must be added if IPv6 is the preferred network protocol.

For more information about the DNS attributes for common components, see Managed Object Model (MOM).

To identify the Diameter object for the DNS LDAP object:

1. Supply the distinguished LDAP name for the DNS object. Enter the MTAS address as local address and one or several (one primary and one or several secondary) DNS servers:

   dn: applicationName=DNS, nodeName=<applNodeName>

An example of how to configure DNS for IPv6 is shown in Example 4.

dn: applicationName=DNS, nodeName=jambala
DnsLocalAddress: [2001:1B70:4292:0251::76]
objectClass: DNS-Application
DnsServerEntry: 0:[2001:1B70:4292:0250::4]:53
DnsServerEntry: 1:[2001:1B70:4292:0251::6]:53

3.5.6   Perform Health Check

Before activating the MTAS, ensure that the MTAS is operational by performing a health check, see MTAS Health Check.

3.5.7   Activate MTAS

After IPv6 configuration for the MTAS is performed, the MTAS must be activated.

To activate the MTAS:

1. Activate the MTAS, see Section Activating MTAS in MTAS VNF Management Guide.
2. Move the traffic from the secondary MTAS to this MTAS.

3.5.8   Perform a Backup of MTAS

Perform a backup, see Create Backup and System Backup and Restore.