Create SSH Public Key

1	Introduction
1.1	Prerequisites
2	Procedure

1 Introduction

This document describes how to create a Secure Shell (SSH) public key managed object for the local Operation and Maintenance (O&M) user account. The SSH public key is an alternative authentication method for the password authentication. The SSH public key is used to check that the user has the correct private key. O&M users are allowed to create, change, and delete their own SSH key.

1.1 Prerequisites

This section describes the prerequisites, which must be fulfilled before using the procedure.

1.1.1 Conditions

The following conditions must apply:

The user is familiar with the security policy of the organization.
The public key is known.
An Ericsson Command-Line Interface (ECLI) session in Exec mode is in progress.

2 Procedure

To create an SSH public key:

Navigate to the UserAccount Managed Object (MO), for example:
>dn ManagedElement=NODE06ST,SystemFunctions=1,SecM=1,UserManagement=1,LocalAuthenticationMethod=1,UserAccountM=1,UserAccount=joedoe
Enter Config mode:
(UserAccount=joedoe)>configure
Create the SSH public key MO, for example:
(config-UserAccout=joedoe)>SshPublicKey=1
Set the attribute publicKeyContent to the public SSH key of the user, for example:
(config-SshPublicKey=1)>publicKeyContent="ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCalZLZKdbq2Ki5n+fMjnx3xLI8YdrgUeme/HwtU2TK377WoKOVmbFlJwkD+Vw8Kb6yHEyGP8SLYcnHmqbjOqhpqOyxgm76iQq3EX1Ueu/5PetBKomVSH3XhxpxNg+1WRwg03EQT2+61shy5lm6EHJG2il+7vc4QFOBxrHxC6SW8O2UjeSIuPFYBZAZ05Wzy2r06X5vLZyokzzcHRqJMzAGxhb+Zg7OWzBFpCj/xCb34Bx6H+DXY1TfYoeV/U8ra5RIBX3Hj0AwcWWA+d8UPUrlhEpkzhJ2b29X4Wk17wJqMiBi69w8wgkyFZLk8GEjMR1hEWVyN5vZ5EH/IRSj6kjN joedoe@SC-1"

Note:
The public key content is to be either in OpenSSH key format or entered in Base64 format without line breaks of an RFC 4716, PEM, or PKCS8 formatted key content (use command: base64 -w 0 content_file).

Note:
The private key should always be protected with a password.
Commit the setting:
(config-SshPublicKey=1)>commit

Verify the setting:

(SshPublicKey=1)>show -v -r

The following is an example output:

SshPublicKey=1
    publicKeyContent="ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCalZLZKdbq2Ki5n+fMjnx3xLI8YdrgUeme/HwtU2TK377WoKOVmbFlJwkD+Vw8Kb6yHEyGP8SLYcnHmqbjOqhpqOyxgm76iQq3EX1Ueu/5PetBKomVSH3XhxpxNg+1WRwg03EQT2+61shy5lm6EHJG2il+7vc4QFOBxrHxC6SW8O2UjeSIuPFYBZAZ05Wzy2r06X5vLZyokzzcHRqJMzAGxhb+Zg7OWzBFpCj/xCb34Bx6H+DXY1TfYoeV/U8ra5RIBX3Hj0AwcWWA+d8UPUrlhEpkzhJ2b29X4Wk17wJqMiBi69w8wgkyFZLk8GEjMR1hEWVyN5vZ5EH/IRSj6kjN joedoe@SC-1"
    sshPublicKeyId=1

Note:: If password authentication is not used, it is recommended to remove the password-based authentication, refer to Remove Password from User Account.