| Attributes |
integerKeyString
key
mandatory
noNotification
restricted |
-
mtasHold
-
This attribute defines the primary key of MtasHold and this section describes the MtasHold attributes.
|
BasicAdmState |
-
mtasHoldAudioAnnouncement
=
LOCKED
-
This attribute defines if an audio network announcement must be played. When the attribute is enabled, and the held stream is an audio stream, an audio announcement corresponding to the value of the mtasHoldCodeAudio attribute will be played to a held user. Service orders this announcement to be played indefinitely. This also means the service stops the announcement.
Takes effect: New session
|
MtasUint00000to065535DT |
-
mtasHoldAudioCode
=
0
-
This attribute defines which audio announcement is to be played to a held user, when only the audio stream is on hold. The code corresponds to the relation between codes and announcements setup in utilized MRFPs. Service orders this announcement to be played indefinitely. This also means the service stops the announcement.
Takes effect: New session
|
MtasUint00000to065535DT |
-
mtasHoldAVAudioCode
=
0
-
This attribute defines which audio announcement is to be played to a held user, when both the audio and video streams are on hold. The code corresponds to the relation between codes and announcements setup in the utilized MRFPs. Service orders this announcement to be played indefinitely. This also means the service stops the announcement.
Takes effect: New session
|
MtasUint00000to065535DT |
-
mtasHoldAVVideoCode
=
0
-
This attribute defines which video announcement is to be played to a held user, when both the audio and video streams are on hold. The code corresponds to the relation between codes and announcements setup in the utilized MRFPs. Service orders this announcement to be played indefinitely. This also means the service stops the announcement.
Takes effect: New session
|
MtasHoldBandwidthOptimizationBehaviourDT |
-
mtasHoldBandwidthOptimizationBehaviour
=
SIP_INSTANCE_DEPENDENCY
-
This attribute defines whether Call HOLD service shall check +sip.instance feature tag in the Contact header in the REINVITE/UPDATE request invoking the Call Hold/Resume procedure to provide bandwidth optimization. It recommended to set the attribute value to 1(NO_SIP_INSTANCE_DEPENDENCY).
Takes effect: New session
|
BasicAdmState |
-
mtasHoldBandwidthOptimizationMode
=
LOCKED
-
This attribute specifies whether bandwidth optimization shall be used for Hold.
- If the attribute is set to LOCKED (0), no bandwidth optimization is done, i.e. the bandwidth reserved for the held session cannot be reused.
- If the attribute is set to UNLOCKED (1), then bandwidth optimization is enabled, i.e. the bandwidth reserved for the held session can be reused for a new call.
Takes effect: New session
|
BasicAdmState |
-
mtasHoldSupportNon3GPP
=
LOCKED
-
This attribute controls if non 3GPP transitions are to be supported.
Takes effect: New session
|
BasicAdmState |
-
mtasHoldVideoAnnouncement
=
LOCKED
-
This attribute defines if a video network announcement must be played. When the attribute is UNLOCKED (1), and the held stream is a video stream, an announcement corresponding to the value of the mtasHoldVideoOnlyCode attribute, or to the values of the mtasHoldAVVideoCode and mtasHoldAVAudioCode attributes, will be played to a held user. Service orders this announcement to be played indefinitely. This also means the service stops the announcement.
Takes effect: New session
|
MtasUint00000to065535DT |
-
mtasHoldVideoOnlyCode
=
0
-
This attribute defines which video-only announcement is to be played to a held user, when only the video stream is on hold. The code corresponds to the relation between codes and announcements setup in utilized MRFPs. Service orders this announcement to be played indefinitely. This also means the service stops the announcement.
Takes effect: New session
|