Contents

1   Description

This instruction describes how to create a threshold monitoring job. A new threshold monitoring job can be created by the user to raise threshold alarms on supported measurement types that are currently not monitored through alarms.

2   Procedure

2.1   Create Threshold Monitoring Job

Prerequisites

• No documents are required.
• No tools are required.
• The following conditions must apply:
  • A unique PmJob Managed Object (MO) name is chosen. To check names already in use, refer to List Performance Management Jobs.
  • The measurement type has threshold alarm support. To check this, refer to List Performance Management Groups and Measurement Types.
  • The thresholdLow, thresholdHigh, and thresholdSeverity attributes are known.
  • The MeasurementType MO is known.
  • An Ericsson Command-Line Interface (ECLI) session in Exec mode is in progress.

Steps

1. Navigate to the Pm MO, for example:

   >dn ManagedElement=NODE06ST,SystemFunctions=1,Pm=1

2. Enter Config mode:

   (Pm=1)>configure

3. Create a threshold monitoring job, for example:

   (config-Pm=1)>PmJob=POT_Thr_Job

4. Set the PmJob initial state to STOPPED:

   (config-PmJob=POT_Thr_Job)>requestedJobState=STOPPED

5. Set attribute jobType to THRESHOLD:

   (config-PmJob=POT_Thr_Job)>jobType=THRESHOLDJOB

6. Create a measurement reader for each referred measurement type, for example:

   (config-PmJob=POT_Thr_Job)>MeasurementReader=POT_mr

   (config-MeasurementReader=POT_mr)>measurementSpecification

   (config-measurementSpecification)>measurementTypeRef="ManagedElement=NODE06ST,SystemFunctions=1,Pm=1,PmGroup=DbsPOT,MeasurementType=PotInst.Count"

   (config-measurementSpecification)>up

7. Create a PmThresholdMonitoring MO, for example:

   (config-MeasurementReader=POT_mr)>PmThresholdMonitoring=POT_tm

   (config-PmThresholdMonitoring=POT_tm)>thresholdLow=10

   (config-PmThresholdMonitoring=POT_tm)>thresholdHigh=100

   (config-PmThresholdMonitoring=POT_tm)>thresholdSeverity=MAJOR

8. Are more PmThresholdMonitoring MOs to be created?

   Yes: Continue with the next step.

   No: Proceed with Step 11.

   Note:  

   Up to four PmThresholdMonitoring MOs can be created. The intervals of these MOs must not overlap.

   
   
9. Navigate to the MeasurementReader MO:

   (config-PmThresholdMonitoring=POT_tm)>up

10. Proceed with Step 7.
11. Repeat Step 6 through Step 8 as needed for each referred measurement type.

    Note:  

    One MeasurementReader MO is needed for each reference to a MeasurementType MO.

    
    
12. Commit the changes:

    (config-PmThresholdMonitoring=POT_tm)>commit

13. Verify the result:

    (PmThresholdMonitoring=POT_tm)>up

    (MeasurementReader=POT_mr)>up

    (PmJob=POT_Thr_Job)>show -v -r

    The following is an example output:

    PmJob=POT_Thr_Job compressionType=[] <empty> currentJobState=STOPPED <read-only> granularityPeriod=FIFTEEN_MIN <default> jobControl=FULL <default> <read-only> jobGroup=[] <empty> jobPriority=MEDIUM <default> jobType=THRESHOLDJOB pmJobId="POT_Thr_Job" reportContentGeneration=CHANGED_ONLY <default> reportingPeriod=FIFTEEN_MIN <default> requestedJobState=STOPPED MeasurementReader=POT_mr measurementReaderId="POT_mr" measurementReaderNameValue=[] <empty> <read-only> measurementSpecification groupRef=[] <empty> measurementTypeRef="ManagedElement=NODE06ST,⇒ SystemFunctions=1,Pm=1,PmGroup=DbsPOT,MeasurementType=PotInst.Count" [...] PmThresholdMonitoring=POT_tm pmThresholdMonitoringId="POT_tm" thresholdHigh=100 thresholdLow=10 thresholdSeverity=MAJOR