1 Start Failure.
2 Stop Failure.
3 Get Failure.
4 Operation allowed in Service Mode only.
5 Maximum number of sessions exceeded. Request denied.
6 PA Fail.
7 Start Failure due to existing application already running.
8 Stop Failure due to non-existing application.
9 Session for command DOES NOT exist.
10 Maximum number of CSS's exceeded. Request Denied.
11 Requested mode is invalid.
12 Channel Number is invalid.
16 Set transmitter or receiver state not successful.
17 Station Power Error during Alignment.
18 Launchtime Offset Not Applicable.

129 Start Failure.
130 Stop Failure.
131 Get Failure.
132 Operation allowed in Service Mode only.
133 Maximum number of sessions exceeded. Request denied.
134 PA Fail.
135 Start Failure due to existing application already running.
136 Stop Failure due to non-existing application.
137 Session for command DOES NOT exist.
138 Maximum number of CSS's exceeded. Request Denied.
139 Requested mode is invalid.
140 Channel Number is invalid.
141 Set transmitter or receiver state not successful.
142 Station Power Error during Alignment.
143 Launchtime Offset Not Applicable.
144 RSSI Measurement cannot be started as RX is Inhibited.
145 RSSI Measurement terminated as RX is Inhibited.
146 Requested Channel is not Configured.
147 Operation allowed in Normal Mode only.

-327680 Please Wait. Calibration In Progress.
-327681 Calibration Process Is Complete.

-327700 Unable To Establish Communication. Start Session Failed.
-327730 Transmitter State Could Not Be Changed.
-327731 Receiver State Could Not Be Changed.

-327687 This operation requires a Device Reset.\nWhile the Device is  resetting, communication\nwith the Device is  not possible.\nAll Real Time Service screens will be closed.\nDo you wish to proceed?
-327683 This operation requires that the application \nbe reinitialized to the requested Mode. \nAll Real Time Service screens will be closed. \nDo you wish to proceed?
-327682 Unable To Perform RSSI Calibration.
-327684 Unable To Change Operational Mode Of The Station.
-327685 Invalid Value. Please Enter A Valid Value.
-327686 Invalid Value. Please Enter A Valid Value.
-327688 Unable To Get Simulcast Transmit Offset Delay From The Station.
-327689 Simulcast Test Pattern Could Not Be Initialized/Terminated In The Station.
-327690 Unable To Get Transmitter Frequency From Station.

-327691 Unable To Get Receiver Frequency From Station.
-327692 Unable To Get Mode From The Station.
-327693 Unable To Set Simulcast Transmit Offset Delay.
-327694 Transmitter Is Not Idle! Please Stop Transmitter Test Or \nAny Test Patterns You May Be Running Before Attempting To Align.
-327695 Transmitter Is Inhibited. Cannot Proceed With Power Amplifier Alignment.
-327696 Hardware Failure. Could Not Complete Power Amplifier Alignment.
-327697 Power Amplifier Alignment In Progress.
-327698 Power Amplifier Alignment Successful.
-327699 PA Alignment Timed Out. No Response From The Station.
-327701 Unable To Set Analog Simulcast Transmit Offset Delay.

-327730 Transmitter State Could Not Be Changed.
-327731 Receiver State Could Not Be Changed.
-327732 Unable To Get Date And Time From Device.
-327733 Unable To Reset Station.
-327734 Transmitter Test In Progress.
-327735 Transmitter Test Was Successful In The Station.
-327736 Transmitter Test Failed In The Station.
-327737 During The Reset, Communication With The Device Is Not\nPossible And All Real Time Service Screens Will Close.\nDo You Wish To Proceed?
 
-327780 Internal Protocol Information Error. 
-327781 DEVICE_ERRORLOG_PROTOCOL_UNKNOWN 
-327782 DEVICE_ERRORLOG_FIEL_NOT_SUPPORTED
-327783 INTERNAL_ERROR_FAIL_TO_GET_REPORT
-327784 DEVICE_IN_FAILURE_MODE
-327785 DEVICE_BUILD_CMD_FAILED
-327786 DEVICE_TRASFER_CMD_FAILED
-327787 DEVICE_BUSY_STATE_ERROR
-393271 Unable To Communicate With Device.

-327830 Unable To Start Measurement Session On The Device.
-327831 Unable To Start Transmitter Metering On The Device.
-327832 Unable To Stop Transmitter Metering On The Device.
-327833 Unable To Stop Measurement Session On The Device.
-327834 Transmitter Test Interrupted.
-327835 Transmitter Test Not Executed.
-327836 Transmitter Test Not Executed! Transmitter Inhibited.
-327837 Transmitter Test Not Executed! DFB Enabled.
-327838 Transmitter Test Not Executed! Station Is Not In Service Mode.
-327839 Transmitter Test Already Running.
-327840 Unable To Establish Communication. Stations Mode Has Not Been Changed.
-327841 Unable to Start RSSI Measurements In The Station.
-327842 Unable to Stop RSSI Measurements In The Station.
-327843 Unable To Start BER Measurements In Station.
-327844 Unable To Stop BER Measurements In The Station.
-327845 Pattern Test Not Supported.
-327846 Unable To Establish Communication With The Station. Pattern Transmission Has Not Been Initiated.
-327847 Unable To Start Test Pattern.
-327848 Test Pattern Running.
-327849 Unable To Stop Test Pattern.
-327850 Transmitter Is Disabled.
-327851 Transmitter Is Failed.
-327852 Invalid Test Pattern Request.
-327853 Transmitter Is In An Unknown State.
-327854 Unable To Initialize Screen. Can't Start Session.
-327855 Can't Get Device Mode.
-327856 This Operation Requires A Station Reset. Do You Wish To Proceed?
-327857 Unable To Change Operational Mode Of The Station.
-327858 Test Is Running ! Do You Want To Stop The Test?
-327861 Transmitter Test Not Executed! Unknown Error.
-327862 Device Configuration does not support transmit functions.
-327863 Unable To Read TDMA Mode Parameter.
-327864 Unable To Get Analog Simulcast Transmit Offset Delay From The Station.

-327880 Unable To Start BER Measurement In Station
-327881 Unable To Start RSSI Measurement In Station

-393271 Unable To Communicate With Device.

-610304 Unable To Start Miscellenous Session On The Device.
-610305 Unable To Start Exciter Metering On The Device.
-610306 Unable To Stop Exciter Metering On The Device.
-610310 Unable To Start Receiver Metering On The Device.
-610311 Unable To Stop Receiver Metering On The Device.
-610321 Unable To Start Power Supply Metering On The Device.
-610322 Unable To Stop Power Supply Metering On The Device.

-610331 Unable To Start UHSO Metering On The Device.
-610332 Unable To Stop UHSO Supply Metering On The Device.
-610333 Station is not in Service or Normal Mode.
-610334 Unable to Key up the station             
-610335 Unable to Dekey the station.
-610336 Unable to Turn PA Test On.
-610337 Unable To Tuen PA Test Off.

-620000 Transmitter Test Timed Out. No Response From The Station.
-620001	Transmitter Test Not Executed! Station mode is not Normal or Service.
-620002 Trouble reading data from the device.\nNot all data is available.

-630400 Receiver Test passed.
-630401 Receiver Test not executed;\nStation mode is not Normal or Service.
-630402 Receiver Test not executed;\nReceiver Failure.
-630403 Receiver Test not executed;\nReceiver Inhibited.
-630404 Receiver Test not executed;\nUnknown error.
-630405 Receiver Test in progress.
-630406 Receiver Test failed.

-630500 Unable To Change RX PL State to 'Turn OFF RX Qualifiers'
-630501 Unable To Change RX PL State to 'Turn ON RX Qualifiers'

-630510 Unable To Change TX PL State to 'OFF'
-630511 Unable To Change TX PL State to 'ON'

-630520 Unable To Change Selective Alarm State to 'OFF'
-630521 Unable To Change Selective Alarm State to 'ON'
