0. 
1. Problem encountered in swapping defaults.
2. FID_TABLE can not be accessed.
3. Loading. Please wait...
4. Warning: Auxio X could not be changed on the TDM slot selected.
5. Error: Valid output numbers for this AEI board are 1 to 7.
6. Error: This is not a valid response, Press F1 for help.
7. Error: Invalid Size Code.
8. Error: The TDM slot entered does not contain a 16 I/O board.
9. Error: The TDM slot entered does not contain a BIM or a DR.
10. Error: The TDM slot entered does not contain a TOMI or non-trunking OMI.
11. Error: The maximum number of channels has been exceeded.
12. Error: The channel you have selected is used elsewhere on this op.
13. Error: The fleet is out of range for the size code.
14. Error: The subfleet is out of range for the size code.
15. Error: The individual is out of range for the size code.
16. Error: The system id was not found, press F1 for help.
17. Error: The trunking system, fleet, and subfleet specified were not found.
18. Error: You must select a conventional CCM for this option.
19. Error: You must select a trunking CCM for this option.
20. Error: Console type does not exist.
21. Error: There are not enough empty CCSMs at the selected location.
22. Error: The maximum number of %s has been exceeded.
23. Error: Auxio card II does not have an output for auxio X.
24. Error: Could not add Call Check on this op.
25. Error: You cannot change mandatory CCSMs.
26. Error: Operator ID Out of Range.
27. Error: You may not alter this CCM type.
28. Error: There is no AEI for this board number. Add AEI first.
29. Error: Valid output numbers for this AEI board are 1 to 4.
30. Error: Heap error.
31. Warning: No available full-duplex, non-dialdown SPI's.
32. Error: Valid size codes are A-K, M, O, or Q.
33. Error: A dual receive board only has input auxios.
34. Error: The new talk group already exists on TDM slot %s.
35. Error: You cannot edit an empty slot. Use add.
36. Error: To select a K option, select the first CCSM in that K option.
37. Error: A DR cannot be added on an odd TDM slot.
38. Error: A DR requires two consecutive empty slots.
39. Error: You can only add a board to an empty TDM slot.
40. Warning: No type of base station control is specified.
41. Error: C.O.R., High Speed Mute, and Takeover are incompatible.
42. Error: Main Standby 2W and Main Standby 4W are incompatible.
43. Error: PL strip is only compatible with T1 Paging base stations.
44. Error: Enter main and alternate TDM slots if redundant BIMs is specified.
45. Error: Either the main or alternate TDM slot must be the current slot.
46. Error: The main TDM slot that you selected contains a non-BIM board.
47. Error: The alternate TDM slot that you selected contains a non-BIM board.
48. Error: BID code selected is already used by TDM slot %02X. Try another.
49. ERROR: Unable to read EMAC Group Database for TDM %s
50. Error: This frequency is already used for repeater %02d.
51. Error: Enter Main or Alternate since this is a separate repeater system.
52. Error: Download or add a TIMI for this system before adding TBIMs.
53. Error: The Transmit slot selected does not contain a TNNR BIM.
54. Error: PL Strip and DC Competitive Control are incompatible.
55. Error: Enter a letter as the first digit.
56. Error: The redundant DR slot selected contains a non-DR board.
57. Error: System IDs must be unique.
58. Error: A TDM slot %02X selected contains a non-CIMI board.
59. Error: Either the Main or Alternate DR slot must be the current slot.
60. Error: The maximum number of trunking systems has been exceeded.
61. Error: The MID code selected is already used by TDM slot %02X.
62. Error: For redundant Centrals the switch mechanism must be specified.
63. Error: Select either PL Strip or DC Comp Ctl for T1_Paging.
64. Error: The switch BIM TDM slot contains a non-BIM board.
65. Error: The switch BIM TDM slot does not contain a BIM or TBIM.
66. Error: One of the TIMI TDM slot fields must be the current slot.
67. Error: A TDM slot %02X selected contains a non-TIMI board.
68. Error: The TIMI at TDM slot %02X already belongs to another system.
69. Error: You cannot delete an empty slot.
70. Error: Delete the CCM or channel from TOMIs first.
71. Error: The failsoft TDM slot selected does not contain a TBIM.
72. Error: There are no FID auxios on this TDM slot.
73. Error: No available inputs at this TDM slot.
74. Error: No available outputs at this TDM slot.
75. Enter size code for new fleet.
76. Error: This k option is not compatible with the tone table.
77. Error: This k option is not compatible with the DC table.
78. Error: A repeater function cannot be used without tone or DC control.
79. Error: There are too many channels on this track.
80. Error: The CCSM being added already exists on this op.
81. Error: The TBIM selected is not part of the current system.
82. Error: This k option is incompatible with the type of channel.
83. Error: The BID code is already used by another channel, Try another.
84. Error: Enter 2 digits (Use leading zero's).
85. Error: The TDM slot is out of range.
86. Error: Insufficient memory.
87. Error: DC Comp. Control is only compatible with T1 Paging Base stations.
88. Error: The repeater number is out of range.
89. Error: The frequency is out of range.
90. Error: Not enough room in original slot to perform move.
91. Error: Not enough room in destination slot to perform move.
92. Error: Swapping model numbers would exceed CCP boundaries.
93. WARNING: HIDDEN channels on this OP will NEVER receive audio (SEE HELP).
94. Error: If 1 of fleets 0XX-7XX has size code Q, fleets 0XX-7XX must be Q.
95. Warning: No Channels were found for the TRACK, BOARD and OUTPUT entered.
96. Error: Could not read file TDM. Download personality PROMs first.
97. Error: Could not add a transmit channel for TNNR added.
98. Error: You must have a TOMI codeplug on the disk to use this option.
99. Error: You must have a LOMI codeplug on the disk to use this option.
100. Error: %s file is too large to program.
101. Error: Timed out while downloading.
102. Error: Could not communicate with TTY port, check connection.
103. Error: TDM slot selected does not contain the selected omi type.
104. Timed out while loading.
105. Download corrupted.
106. Error occured during download.
107. Dataio Setup failed.
108. DC Competitive Control cannot be specified on a BIM without DC Control.
109. Error: The version of this default file is not compatible with the fpp.
110. Address out of range.
111. No response received from LDI PROM programmer, please check connection.
112. Download complete. Ready to download next PROM or download EEPROMs.
113. No response received from PROMPRO8X, please check connection.
114. No codeplugs for this customer.
115. Could not read in k option table. Press any key.
116. Could not read in model num table. Press any key.
117. Error: Valid baud rates are 9600, 4800, 2400, 1200, and 300.
118. Could not create directory.
119. Could not set directory current.
120. The backup directory cannnot be the same as the customer directory.
121. You must use DOS version 3.0 or greater to run this program.
122. No disk was found at drive 
123. Error: Duplicate record already exists: CEB %02d, slot %02d, freq %02d.
124. Error: FFFF is an invalid system id.
125. Error: Invalid node type.
126. Error: The slot selected is already part of another redundant pair.
127. Error: The 2 transmit slots selected cannot be the same TDM slot.
128. Error: FPP internal error: %s.
129. Error: Invalid Supervisor Status. Must be 1, 2 or 3.
130. Error: Max number of SIGBIM's is %d.
131. Error: Max number of TOMI's is %d.
132. Error: The selected failsoft TBIM is being deleted.
133. Error: Individual ID already in use.
134. Error: Valid COM ports are 1 and 2.
135. Error: The selected COM port is not installed.
136. Error: CCP number out of range for this console type.
137. Error: Invalid slot number. Valid slots are 1 - 8.
138. Error: No select button found in the CCP and slot selected.
139. Error: Invalid location.
140. Error: FID entered does not exist for this K option.
141. Error: Invalid auxio card number.
142. Error: Invalid auxio number entered.
143. Error: Too many retries from TTY port.
144. Uploading. Please wait...
145. Error: The EEPROM part is damaged.
146. Error: Unknown status received from TTY port.
147. Error: The EEPROM is the wrong size for permanent data.
148. Upload complete!
149. Downloading. Please wait...
150. Warning: The EEPROM contains invalid data. Defaults will be created.
151. Download complete!
152. Setting up CEB. Please wait...
153. Error: Wrong board type.
154. Error: Wrong TDM slot.
155. The persprom version is too old. Read persprom before reading eeprom.
156. Error: Could not decode trunking ID.
157. Error: Invalid fleet. Must enter 3 digits.
158. Error: Invalid individual id. Must enter 3 digits.
159. Error: Invalid system id. Must enter 4 digits.
160. Error: No TOMI EEPROM found on disk or you do not have RF Signalling.
161. Error: Invalid TDM slot, Press F9 to see available TDM slots.
162. Error: Valid size codes are A-K, M, O, Q, or U.
163. Error: You must enter a valid speaker destination.
164. Error: No TOMI or LOMI codeplugs found on disk for this customer.
165. Warning: Console Params data from disk was corrupted.
166. Error: Valid serial baud rates are 9600, 4800, and 2400.
167. Setting up communication with PROM programmer. Please wait...
168. Error: Could not fill RAM.
169. Error: THERE MUST BE A DVP TBIM TO USE THIS OPTION.
170. Error: Invalid conventional channel.
171. Error: No match found for pattern entered.
172. Error: Please enter an alias to search for.
173. Error: Enter 2 digits or ** for all OPs.
174. Error: Not enough room to duplicate alias list.
175. Error: You cannot copy an op onto itself.
176. Error: Invalid OP TDM slot.
177. Error: There is no EEPROM file for this TDM slot.
178. Error: Alias database not found in EEPROM file.
179. Error: There is no more room to add another alias.
180. Error: Integrated Voice activity and channel free tone are incompatible.
181. Error: The field prom programmer is obsolete for this prom.
182. Error: There are no TOMI EEPROMs downloaded to the disk.
183. Error: Add COR on the corresponding BIM in the personality PROM first.
184. Error: New model number not found in MODEL TABLE. Press any key.
185. Error: Enter 2175 or 1200.
186. Error: Enter a value which is a multiple of 100.
187. Error: Value entered is out of range.
188. Error: Enter a value which is a multiple of 10.
189. Error: Invalid opids for this modem will not be saved.
190. At users request, opid's for this modem will not be saved.
191. This modem's OPIDs are already on disk. They will not be saved again.
192. Error: The new OPID matches another opid in this unique-opid system.
193. Error: Cannot save yet - invalid inputs.
194. Error: Cannot decode current alias's unit id.
195. Error: Invalid Alias type. Enter 1 - 5.
196. Error: Invalid channel type. Enter 1 - 4.
197. Error: Invalid data for TRUNKING UNIT ID.
198. Error: Invalid UNIT ID.
199. Error: Invalid BID code. Enter 2 digits.
200. Error: PCIIE: off-hook timeout must be less than hangup timeout.
201. Error: Can't create a memory file for CRT incompatability screen.
202. Error: Can't dsply CRT incompat scrn, file 'misc_1.txt' not found.
203. A TYPE_II channel that is not private call must have a valid group id.
204. Error: Invalid channel type.
205. Error: One of the CIMI TDM slot fields must be the current slot.
206. Error: OMI IN TDM SLOT %02X ALREADY HAS PRIMARY SUPERVISOR STATUS.
207. Error: lack of space to save new databases - needed %ld - found %ld.
208. Error: Cannot save %s database to disk
209. Error: Cannot read channel database for %02X tdm slot
210. Error: All inputs are not yet valid.  Please continue entering.
211. Error: The file %s cannot be accessed.
212. Error: Invalid individual opid.
213. Error: Group opid out of range.
214. Error: Invalid input character.  Try again.
215. Error: EEprom file not created for tdm %02X.  Cancelling save request.
216. Error: ID doesn't match current TalkGrp ID E%03X in same-OPID system.
217. Error: ID doesn't match current INDVD OPID %04X in same-OPID system.
218. Error: Invalid Frequency Scheme.  Press F9 for list of valid schemes.
219. Error: THERE MUST BE A DVP OR ASTRO TBIM TO USE THIS OPTION.
220. Error: Invalid width of text lines. Press any key.
221. Error: Can't display Y/N prompt (text too long). Press any key.
222. Error: Can't create a memory file for fld_prog.exe.
223. Error: Can't read in text strings, can't find file: 
224. Error: Couldn't find row in memory file.
225. Error: Problem with channel database.
226. Error: Freq. minus base freq. must be a multiple of channel separation.
227. Error: A negative number is not valid.
228. Error: Lowest channel number must be less than the highest channel number.
229. Error: SMARTNET types are 1-Type I, 2-Type II, or 3-Type I Aliased.
230. Error: Enter F or S for Fleet or Subfleet.
231. Error: Invalid group id.
232. Error: Invalid individual id.
233. Warning: PC capable required for PC enhanced.  Set to 'N'.
234. Warning: ENTER ID switch required for Mobiles Type 2, 3. Set to 1.
235. Error: Encoded Trunk ID is within the Type II ranges for this system.
236. Error: 'From' value must be smaller or equal to 'to' value.
237. Error: Value [%04X] is not in any of the ranges entered.
238. Error: Smartnet type cannot be TYPE_I_ALIASED (3) for PRIVATE CALL.
239. Error: Smartnet must be TYPE_II (2) for B1675.
240. Error: Available SMARTNET types are 1-Type I or 2-Type II.
241. Error: The trunking data entered encodes to an invalid trunking id.
242. Error: problem decoding alias, press any key to continue.
243. Error: a fleetwide alias can not be regroupable, changed to 'N'.
244. Error: The BID Code entered was not found on any of the PROMs on disk.
245. Error: cannot have both transmit timeout and RF signalling BIM
246. Error: P6 is jumpered wrong or EEPROM is corrupted.
247. Error: TDM slot in EEPROM does not match DIP switch setting on board.
248. Error: Personality PROM has changed. EEPROM data is no longer valid.
249. Error: Bad Database version in EEPROM.
250. Warning: Node_type not correlating with base_type.
251. Warning: You changed the node. CCMs for this slot may not be compatible.
252. Error: This is not a valid node type, press F1 for help.
253. Warning: Speaker destination is out of range for assignable speakers.
254. Error: FPP is obsolete for this Personality PROM.
255. Error: TDM Slot is node %s, model number requires node %s.
256. The node on the redundant BIM will also be updated to what you selected.
257. The timeout time on the redundant BIM will also be updated.
258. read node file has failed.
259. Warning: Speaker not found in assignable speaker database.
260. Warning: Speaker already exists in assignable speaker database.
261. Warning: Personality PROM Catalog Checksum error.
262. Error: Operator Status Number out of range.
263. Error: This model can only be added if the keypad type is alpha-numeric.
264. Error: Can't create a memory file for AKM set up help screen.
265. Error: Can't dsply AKM set up help scrn, file 'misc_2.txt' not found.
266. Error: Invalid Stack Size.  Valid Stack Sizes are 2-10.
267. Error: BIM is not a Signalling BIM.
268. Error: Invalid System ID.  Valid System IDs are 0 and 1.
269. Error: Default database %d has a bad length - will not overwrite.
270. Error: Only M, E, or N are valid entries.
271. Using customer EEPROM defaults.
272. Using EEPROM defaults in default directory.
273. Error: Your slot rcvr to mux bus mapping won't work with assign speaker.
274. Error: Missing a database from the EEPROM. Cannot proceed.
275. Error: No room for 8 line display module to left.
276. Error: Delete or move used CCSM's in CCM to left for 8 line display.
277. Warning: Do not exceed number of phantom channels over 50.
278. Error: Valid Mobiles/Portables Types are 1, 2, or 3.
279. Error: CEB ID out of range.
280. Error: CMT aliases in use. Change aliasing data is illegal.
281. Error: Must use RS232 Link to CEB to program and read AIMI persproms.
282. Error: AEB ID out of range.
283. Error: Invalid bid code.
284. Error: AIMI fixed section is corrupted or missing.
285. Current alias record is blank.
286. Error: There is no more room to add another FID.
287. Error: Cannot delete an auxio that exists on the ops.
288. Error: FID numbers can only be alphanumeric.
289. Error: FID number already exists.
290. Error: Only the even tdm slot is valid for a DR.
291. Error: The slot must be BIM,SBIM,TBIM,DR,or 16 I/O.
292. Error: There can only be one FID per TDM/AUXIO combination.
293. Error: Auxio number must be less than 7 for BIM or DR.
294. Error: Auxio number must be less than 5 for TBIM.
295. Error: Auxio number must be less than 17 for 16 I/O.
296. Error: K143BN is incompatible with FleetWide channels in SmartNet systems.
297. Error: This auxio is unavailable.
298. Error: Cannot find an AIMI cdsect dbase.
299. Error: There must be a DVP or ASTRO BIM to use this option.
300. Error: Use only 0-9, A-Z, *, #, and space.
301. Error: Alias Name cannot be all blanks.
302. Error: Use only 0-9, A-D, F, P, *, and #.
303. Error: Please enter the pattern to search for.
304. Warning: The aliases in the dest op will be destroyed.
305. Error: Wrong array size specified when using strarry.
306. Error: Alias name already exists.
307. Error: AIMI's can only be added on slots 5E and 5F.
308. Error: Failsoft repeater out of range.
309. No dialer databases were found for this customer.
310. Error: Message send failure.
311. Error: Unable to clear dialer board.
312. Error: Not enough memory for dialer database.
313. Error: The auxio selected is already used on this OP.
314. Error: There is no more room to add another FID on this OP.
315. Error: Invalid packet code.
316. Warning: Channel with BID %d CEB %d does not exist.
317. Warning: New redundancy settings affect TDM slot %02X.
318. Error: Unable to set up message layer communications.
319. Decompressing EEPROM.
320. EEPROM defaults have been created for slot %02X.
321. DVP Stat and Main Standby 4W are incompatible.
322. Error: The AMB crossmute files don't exist in the AEB.
323. ERROR: Max number of Non-redundant plus redundant SGBM pairs is %d. 
324. Setting up Ambassador.  Please wait...
325. ERROR: Unable to create Embassy databases.
326. ERROR: Unable to create Embassy signalling structures.
327. ERROR: For an embassy system, NULL_NODE is not acceptable.
328. ERROR: The MAIN or the ALTERNATE_CEB_ID must be this ceb's id.
329. ERROR: The ceb_id of %02d does not exist.
330. ERROR: The MAIN_CEB/MAIN_BID or the ALT_CEB/ALT_BID must be this board.
331. ERROR: The alt_bid_code you selected maps to a TDM of a NON-bim board.
332. ERROR: The main_bid_code you selected maps to a TDM of a NON-bim board.
333. WARNING: There is not a TDM slot in this ceb for the alt bid code.
334. WARNING: There is not a TDM slot in this ceb for the main bid code.
335. ERROR: Main ceb/main bid and alt ceb/alt bid is required if redundant.
336. ERROR: A board can not be redundant to itself.
337. ERROR: The audio TDM slot is out of range for multi-ceb systems.
338. ERROR: This tdm slot does not contain a BIM or signalling BIM.
339. ERROR: RF xmute and RF xmute w/ accoustical cplng are incompatible.
340. ERROR: There should be some type of interference for this BIM.
341. ERROR: Non-existent CEB ID.
342. ERROR: Not enough room left in XMUTE table to make an addition.
343. ERROR: Not enough room left in OFFSET table to make an addition.
344. ERROR: Can't crossmute this type of BIM: %s
345. ERROR: Some/All deletions were not made. Repeat procedure if desired.
346. ERROR: Some/All changes not added. Repeat procedure if desired.
347. ERROR: Cannot crossmute with this frequency.
348. ERROR: This option is for Embassy systems only.
349. ERROR: There is no AIMI PersPROM on disk. Add or download an AIMI PersPROM.
350. ERROR: Valid entries are 1 - 254.
351. ERROR: Invalid fallback action.
352. WARNING: You may have to update your redundancy on ceb %d for bid %d.
353. ERROR: Could not find transmit slot.
354. ERROR: Advanced Securenet requires Tone Control option.
355. The Adv. Securenet option on the redundant BIM will also be updated.
356. ERROR: Adv. Securenet is not compatible with selected Base station type.
357. ERROR: PL options are not compatible with Advanced Securenet option.
358. WARNING:  No .DEF files were found.
359. ERROR: Error in Action Type.
360. ERROR: Dialer alias database is full.
361. ERROR: The entry index requested is invalid.
362. ERROR: Bad data in phone number or alias name.
363. ERROR: Alias not added/removed due to mismatch fields to the dialer.
364. ERROR: Alias entry could not be added due to dialer board error.
365. ERROR: The DIALER board is currently being used.
366. ERROR: Valid entries are 'A', 'M', or 'N'.
367. ERROR: Access code cannot begin with 'E'.
368. ERROR: Valid char's are: 0-9, A-F, and X, excluding the group digit %c.
369. ERROR: The limit is %d variable characters in the repeater access code.
370. WARNING: Add the K option K519AB to enter the variable digits via keypad.
371. WARNING: If DVP is on, turn on encode closure in menu 0473.
372. WARNING: K option X932AA must be added to support man. rptr acc.
373. AEB Data Checking Successful.
374. ERROR: You must have an embassy system to perform AEB checking.
375. ERROR: No CEB data found for AEB.
376. ERROR: Unable to display gauge display.
377. ERROR: Illegal characters in directory name.
378. ERROR: The k-option entered is not compatible on a CRT console.
379. WARNING: Check op position for k-opts incompatible with a CRT console.
380. ERROR: This trunking system already exists in another CEB.
381. ERROR: Not enough space in the EEPROM to store your EMAC database.
382. WARNING: Speaker does not exist. Select another speaker or add a B1403.
383. ERROR: Channel does not exist on this OP.
384. WARNING: Can't reread access code. Please re-enter a value.
385. ERROR: Problem encountered in storing variable digits of access code.
386. ERROR: Problem encountered in storing fixed digits of access code.
387. There are no more available SPI's to add to the list.
388. Invalid TDM. Check TDM database.
389. SETTING UP MESSAGE LAYER COMMUNICATIONS.
390. SETTING UP DIALER ALIASES.
391. CLEARING DIALER BOARD.
392. DIALER UPLOAD COMPLETE!
393. NON-EMBASSY SYSTEM PRESENT
394. The TDM slot selected has auxios of the wrong function type. Use MOVE AUXIOS.
395. WARNING: Not enough space in the EEPROM to store your SPI's and aliases.
396. ERROR: DVP and ASTRO are incompatible.
397. ERROR: TnnR node types incompatible with signalling channels.
398. Compressing EEPROM.
399. Calculating compressed EEPROM size.
400. ERROR: Cannot create default image space.
401. ERROR: File not found. Could not read MDC1200.DEF default file.
402. Using MDC1200 defaults in default directory.
403. ERROR: Invalid base type for ASTRO channel. Press F1 for help.
404. ERROR: Valid ASTRO node types are T1R1, T2R2, and T4R4.
405. ERROR: ASTRO REQUIRES EITHER TRC OR DIGITAL KEYING.
406. ERROR: This is not a SMARTNET system.  Please choose another.
407. ERROR: This is not a SMARTZONE system.  Please choose another.
408. ERROR: This TLINE is in use by another system.
409. ERROR: The TLINE must be between 33 and 35.
410. ERROR: The CONTROLLER ID must be between 01 and 99.
411. ERROR: The default file being read is too large for this FPP.
412. ERROR: Illegal System ID. Enter a valid System ID or add a new system.
413. ERROR: Valid entries are '1' and '2'.
414. ERROR: Valid entries are '1', '2' and '3'.
415. ERROR: Valid entries for audio slots to be summed are 1 - 5.
416. ERROR: Valid TLINE entries are 1 - 32.
417. ERROR: Missing record for this modem in the TOMI eeprom database.
418. ERROR: Need slot for Crossmute Dbs in BIM SELECT SCREEN, MAIN F4 F9 F9 F3
419. ERROR: Valid AEB slots are hexidecimal numbers from 0 to 7F.
420. WARNING: You must program both AMBASSADORS %02X and %02X.
421. ERROR: There is no %s file in the AEB for this board.
422. ERROR: You cannot copy a slot to itself.
423. Error: ID doesn't match current TalkGrp ID A00%04X in same-OPID system.
424. Error: ID doesn't match current INDVD OPID %07lX in same-OPID system.
425. WARNING: DVP was set to N. Turn off encode closure in menu 0473.
426. Error: There are no E1_T1 databases in the AEB directory.
427. ERROR:  Unable to determine size of PERSPROM.
428. ERROR: Valid entries are 'A' or 'B'.
429. ERROR: Valid entries are 1 - 5.
430. ERROR: XBUS requires both Link 'A' and Link 'B' the same.
431. ERROR: Default file is out of date for this FPP. Database %s%02d
432. ERROR: FPP is out of date for this default file. Database %s%02d
433. WARNING: Invalid signalling records exist in TOMI EEPROM.
434. WARNING: Unable to open default file for EEPROM.%2s.
435. ERROR: Minimum lines per page is 30.
436. ERROR: Unable to read Next Free Line Database for TDM %s
437. ERROR: The replacement switch bim can not be the current.
438. ERROR: Blanks are not accepted.
439. RAC Field will be modified with leading zero's for this signalling type.
440. ERROR: Unable to delete last TIMI in this system. Delete all TBIMS first.
441. Valid stack sizes are 2 to 10 only.
442. Valid stack types are 'L' for LIFD and 'F' for FIFD.
443. ERROR: Can not have hidden channels on CRT consoles.
444. ERROR: TDM slot out of range [00 - 5F]
445. ERROR: Group Number out of range [1 - 5]
446. ERROR: Logical group number out of range [0 -255]
447. ERROR: Logical group number already exists for EMAC group %3d
448. ERROR: ETG must be a trunking channel.
449. ERROR: ETG must not be a hidden channel.
450. ERROR: There are no more available channels to add.
451. ERROR: You can not add more than 40 channels to an EMAC group.
452. WARNING: Logical talk group set to an invalid group.
453. ERROR: HIDDEN channels must have all 4 audio fields set to 255.
454. ERROR: Valid selections are from 0 - 3 and 255.
455. WARNING: There are currently no EMAC available channels assigned to this OP.
456. ERROR: Delete this switch's patch group first via menu 0497. 
457. ERROR: A perm. patch group is already using this switch's patch index.
458. ERROR: Only %d members are allowed for a %s group.
459. Error: There are no more available patch resources to add.
460. Error: Can't edit MSEL/Patch groups.
461. Warning: AUXIOs may still reference this TDM slot.
462. ERROR: DIGITAL KEYING CAN ONLY BE USED ON ASTRO CHANNELS.
463. ERROR: EXTENDED TONE CONTROL IS NOT COMPATIBLE WITH DIGITAL KEYING.
464. ERROR: CARRIER OPERATED RELAY MUST BE SELECTED WITH DIGITAL KEYING.
465. ERROR: THIS K OPTION REQUIRES DIGITAL KEYING.
466. ERROR: THIS IS NOT A VALID KEYING METHOD, PRESS F1 FOR HELP.
467. ERROR: THE MODE 1/MODE 2 FIELD REQUIRES ASTRO AND DIGITAL KEYING.
468. ERROR: THIS IS NOT A VALID MODE 1/MODE 2 CONFIGURATION, PRESS F1 FOR HELP.
469. WARNING: THERE ARE NO TYPE II RANGES IN THIS SYSTEM.
470. WARNING: THE DVP, CIU/DIU RECEIVE AUXIO, AND COR PROMPTS WERE RESET TO N.
