  0)%02X
  1)WARNING: No type of base station control was
  2)specified.  Do you wish to change this?
  3)DVP is set to %c, but DVP on other redundant BIM is
  4)set to %c.  Do you wish to change the latter?
  5)BASE TYPE is %s, but it is set to %s
  6)on the other redundant BIM. Do you wish to change the latter?
  7)There is no board in slot %02X.  Is one to be created?
  8)There is no board in slot %02X.  You must enter a TDM slot which has a board
  9)MAIN TRANSMIT SLOT
 10)Slot %02X is empty. You must agree to add a board there, or Abort!
 11)MAIN DR TDM SLOT
 12)MAIN DR slot %02X invalid. Slot must not be empty, or you must add a board there
 13)ALTERNATE TRANSMIT SLOT
 14)ALT XMIT slot %02X invalid. Slot must not be empty, or you must add a board there
 15)TRANSMIT SLOT
 16)XMIT slot %02X invalid. Slot must not be empty, or you must add a board there
 17)OTHER REDUNDANT SLOT
 18)DR slot %02X invalid. Slot must have a DR, or you must add a DR there
 19)You changed from SEPARATE to SHARED TBIM's.  Do you wish
 20)to use (1) MAIN TBIM's or (2) ALT TBIM's? (enter 1 or 2)
 21)These TDM Slots are no longer being used.
 22)    (Press Y when ready to continue)
 23)There is no TIMI in TDM slot %02X.
 24)Are you going to add a new TIMI there?
 25)If you want a TIMI in slot %02X, you must add one there, as it is now empty!
 26)Aborting.  Bad argument list to ck_uaux.
 27)These switches conflict with the option specified.
 28)Use MOVE AUXIOS or delete the switches listed.
 29)LOCATION   SLOT   PANEL   TDM SLOT   AUXIO
 30)OTHER BAND PARAMETERS
 31)Base Frequency (KHz)    :
 32)Channel Separation (KHz):
 33)Lowest Channel Number   :
 34)%s has no board in the designated slot.
 35)Are you going to add a %s in that slot?
 36)Please insert program disk #2 in drive %c: then press return key
 37)Warning: All TOMI(s) not downloaded.   RF SIG BIM not added at tdm: %02X
 38)Do you wish to continue?
 39)This TDM slot: %02X and TDM slot: %02X will both be
 40)changed to BIMS.  Are you sure that you wish to delete
 41)the RF SIGNALLING BIM option from these slots? 
 42)changed to RF SIGNALLING BIMS.  Are you sure that you wish
 43)to add the RF SIGNALLING BIM option from these slots? 
 44)K830 - RF Signalling BIM? (y or n)
 45)45
 46)BIM options for TDM slot 
 47)<== %s
 48)*BASE STATION TYPE
 49)*TYPE OF NODE
 50)%s (y/n) 
 51)*D.C. CONTROL
 52)*TONE CONTROL
 53)*RELAY KEYING CONTROL
 54)*EXTENDED TONE CONTROL
 55)*CARRIER OPERATED RELAY
 56) or %s (y/n) 
 57)*HIGH SPEED MUTE
 58)*SUPERVISOR TAKEOVER
 59)*LORBL
 60)*MAIN STANDBY 2W
 61)*MAIN STANDBY 4W
 62)*RFSIG PROMPT
 63)*TRANSMIT TIMEOUT
 64)*DVP
 65)*BIM DVP RECEIVE AUXIO IN
 66)*MOMENTARY OVERRIDE
 67)*PL STRIP
 68)*DC COMP CONTROL
 69)*DUPLEX
 70)%s(00,01,ff)
 71)*RF SIGNALLING SYSTEM ID
 72)*NO DEEMPH
 73)*ALT TIMING
 74)*BOARD BID CODE
 75)*EMB RED
 76)*MAIN BID
 77)*ALT BID
 78)*MAIN CEB ID
 79)*ALT CEB ID
 80)*REDUNDANT BIMS/DRS
 81)*MAIN TDM
 82)*ALT TDM
 83)*ASTRO MODE
 84)ASTRO is set to %c, but ASTRO on other redundant BIM is
 85)set to %c.  Do you wish to change the redundant BIM?
 86)ZBIM options for TDM slot 
 87)System Id
 88)Tline
 89)Controller Id
 90)Bid Code
 91)Internal System Id 
 92)Did you delete all ZBIMs which reference this system
 93)in other CEBs first?  If not, don't delete the system.
 94)Do you wish to delete system
 95)Are you adding a new system? 
