  0)THE EEPROM FILE ALREADY EXISTS FOR TDM %02X.
  1)DO YOU WISH TO SAVE THE ALIASES FOR THIS TOMI (Y/N)?
  2)DO YOU WANT TO CONTINUE (Y/N)?
  3)*UPLOAD DOWNLOAD
  4)UPLOAD/DOWNLOAD MENU
  5)F2 = Read personality prom data from prom programmer or CEB.
  6)F3 = Read the EEPROM data from the CEB
  7)F4 = Create new EEPROM default database
  8)F5 =
  9)F6 =
 10)F7 =
 11)F8 = Program data into prom programmer or CEB.
 12)F9 = 
 13)0000<
 14)4000;
 15)Make sure the pc com port is connected to the DATAIO
 16)Fill the DATAIO RAM by pressing <Select> A2 FF <Start> for Series22
 17)or <Select> A2 <Start> FF <Start> for 29A or 29B
 18)Put the DATAIO in remote mode by pressing <Select> F1 <Start>
 19)for Series22 and <Select> F1 <Start> <Start> for 29A or 29B
 20)If the baud rate has not been set previously:
 21)On the Prompro 8X, press SELECT to see the ^ prompt, press LIST, type 36
 22)Press RESET, and turn Prompro 8X off and on
 23)Press DEVICE, press NEXT until proper device type is shown
 24)(22B01 and 19B01 parts correspond to the 27128I display)
 25)(The 22B02 part corresponds to the 27128A display)
 26)Press EXIT
 27)Make sure the com port is connected to the Prompro 8X
 28)Insert codeplug in prom programmer socket
 29)Press any key when these steps have been completed
 30)Press enter when these steps have been completed
 31)
 32)
 33)OMI_MENU
 34)DOWNLOAD METHOD MENU
 35)DOWNLOAD A CODEPLUG
 36)1. TOMI
 37)2. LOMI
 38)3. TIMI
 39)4. CIMI
 40)5. AIMI
 41)1. DATAIO PROM PROGRAMMER
 42)2. SHOOTER PROM PROGRAMMER
 43)3. PROMPRO8 PROM PROGRAMMER
 44)4. PROMPRO8X PROM PROGRAMMER
 45)5. RS232 LINK TO CEB
 46)Enter the number of the download method:
 47)Enter the number of the board type:
 48)*OMI TYPE
 49)Enter tdm slot as shown on codeplug label:
 50)An error has occurred during downloading. The operation has been aborted
 51)Press enter to continue
 52)UPLOAD MENU
 53)F1 = Help
 54)F2 = Upload personality prom data into prom programmer/CEB.
 55)F3 = Upload TOMI/MODEM EEPROM data into CEB.
 56)F4 = Upload DIALER ALIAS data into CEB.
 57)F5 = Upload AMBASSADOR data into AMBASSADOR board
 58)F6 =
 59)F7 =
 60)F8 = 
 61)F9 = 
 62)F10 = Exit
 63)Enter the number for the upload method:
 64)Enter the number for the EPROM part number:
 65)*PROGRAM YES/NO
 66)1. Intel 27128 (Motorola 22B01)
 67)2. AMD 27128A/27C128 (Motorola 22B02/88A01)
 68)3. SEEQ 5143 (Motorola 19B01)
 69)4. Intel 27128A/27C128 (Motorola 22B02/88A01)
 70)An error has occurred during uploading. The operation has been aborted
 71)Press enter to continue
 72)Make sure the com port is connected to the RS232 card above the OMI
 73)Set jumpers on RS232 card for correct board type
 74)To see the correct jumpering for each board type press F1
 75)Make sure the com port is connected to the telco connector P3 on the MODEM
 76)Connect the TTY cable to the AMBASSADOR you wish to program
 77)Only one copy of the following databases is kept for all codeplugs
 78)Enter nothing next to the database to use the version already on disk
 79)Enter an 'R' next to the database to use the version from the codeplug
 80)WARNING: For best results only use 'R'
 81)when you have made a mistake in changing one of the databases
 82)WARNING:  The Ambassador files were not found in the AEB directory
 83)specified. Please check to see if this is the correct directory. You
 84)may need to change directories or enter Crossmute data. Press F1 for
 85)further assistance, ESCAPE to return to the Main Menu, or F10 to
 86)return to the Upload menu.
 87)Error: Need a hardlock to upload %s SP for the OP in TDM %s.
 88)Patch
