===========================================================

 SOFTWARE RELEASE NOTE

===========================================================

Product  : Professional GM600/1200 Series FlashGrade Tool
KIT No   : ENVN4027D
Release  : R02.00.20
Date     : 01-Jun-2001
Language : English

===========================================================

 Purpose Of This Release

===========================================================

Supported features:

- Reading Radio information

- Upgrade a radio to software version R02.00.20 from
  previous released versions with hardware codeplug update, 
  and saving of tuning data

Supported Software versions:

- Only official radio software release version and bands.
  In this version:
  R02.00.08, R02.00.13, R02.00.17, R02.00.18
  software is updated to version R02.00.20
  codeplug is updated for all versions

===========================================================

 How To Install And Run This Software

===========================================================

Installation of the software is not necessary. The software
can either be started directly on a floppy disk or on a hard
disk by calling the UpgradeTool.exe file. All files of this
release must be copied to the same directory.

For the usage of this software the following radio accessories
are required:

(A) Flashing via the rear connector:

    - Flash adapter, P/N HLN9742
    and (i)
    - Radio Interface Box, P/N RLN4008
      with battery or power supply
    - RIB to PC cable, P/N 3080369B72 (9pin) or 3080369B71 (25pin)
    - Programming/test cable, P/N RKN4083
    or (ii)
    - RIBless programming cable, P/N RKN4081
    - 10 pin (Mic) to 20 pin (rear) adapter RLN4853

    By using equipment (i) the Flash adapter has to be connected 
    beetween the Radio Interface Box and the Programming/test cable.
    Maximum baud rate for this equipment is 19,200 Bd.

    By using eqipment (ii) the Flash adapter has to be connected
    beetween the PC and the RIBless programming cable.

    For Flash Adapter HLN9742B, "Flash mode on" means switch 
    position "A", position "B" is used for mic connector flashing.

    It is not possible to use Programming cable GTF374 for upgrading 
    radios.

or

(B) Flashing via the mic connector:

    - RIBless programming cable, P/N RKN4081B
    - Flash adapter, P/N HLN9742B
    
    "Flash mode on" means flash adapter switch position "B",
    position "A" is used for rear connector flashing.

    It is not possible to use Programming cable GTF374 for upgrading 
    radios.

===========================================================

 Radio Software Release Note

===========================================================

PRODUCT: WARIS MPT GM640/GM660/GM1280 

VERSION: R02.00.20
DATE OF BUILD : 25-May-2001

Affected Models :

All GM640/680/1280 Preferred, Prime and Popular models.
Does not support Portable radios.

===========================================================

 Associated Software:

===========================================================

CODEPLUG COMPATIBILITY: Release R02.00.20
CPS COMPATIBILITY: Phase 3 CPS only (R00.02.10)

===========================================================

 New Features / Notes:

===========================================================

- ENABLE MAP27 FOR ALL PORTABLE & MOBILE RADIO MODELS
  MAP27 has been enabled for all radio models for both MPT and
  Conventional personalities. This feature was previously only
  available for the GP1280 however it is now available for the
  GP640 & GP680 radio models. 
  The radios have the full functionality of the MAP27 protocol.
  This firmware must be used with the CPS R00.02.10 to enable MAP27.

Fixes the following issues:

- TAUse02013 
  On some conditions of power drop the display of the control head
  does not work.

- TAUse02014
  On some conditions of power drop the radio comes up with minimum
  volume instead of the actually selected one.
