AirOS F Firmware Revision History
====================================================================
Supported products

  * airFiber 24

====================================================================

Changelog: 
--------------------------------------------
Version 2.2.1 (July 17, 2015)
--------------------------------------------
New Features:
- n/a

Improvements:
- n/a

Fixes:
- Addresses vulterability that could allow unauthenticated users to gain access to the device via HTTP(s). All users should update immediately.

Known Issues:
- n/a.

Notes:
- n/a


--------------------------------------------
Version 2.2 (January 5, 2015)
--------------------------------------------
New Features:
- Added Ethernet health monitoring for DATA port
- Added airView support

Improvements:
- Signed airView Java Applet to run on newer Java installations without security exceptions
- Receive signal bar now reads full scale for perfectly aimed link (was 3 db low)

Fixes:
- Fixed formatting errors in SNMP MIB
- Fixed bug on system page where clicking "Check for Updates" would cause "Startup Date" field to become checked as well.
- Fixed problem where ethernet link would never come back after an ethernet Carrier Drop event.
- Fixed main page performance graph freeze on communication error
- Changed min signal on bar graph to -90

Known Issues:
- n/a

Notes:
- n/a

Version 2.0 (March 28, 2014)
--------------------------------------------
New Features:
- added multicast filtering
- added GIGE carrier follows RF link functionality
- added Link up-time display
- added Remote MAC address display
- added Remote IP address display

Improvements:
- Obsoleted ability to read AES key from MIB
- reorganized Main Page to simplify installation
- distance reads in Km/Miles if 1 or greater
- receive power graphs scale with link distance
- reorganized Advanced Page
- changed flow control verbage

Fixes:
- Fixed GIGE Carrier issue that required unit to be rebooted after enabling
- Fixed Power limit issues for some ETSI regions
- Fixed Rx power display issues for ETSI/ACMA regions
  This addressed an ETSI/ACMA issue where the received power displayed 
  values that were 5dB too high. While the rx display is now correct, 
  the actual tx power has not changed. Link performance should not be
  effected.
- Fixed SNMP MIB issue found by openNMS
- Modified Ethernet transciever programming to address CRC errors

Notes:
- removed Temperature readings
- updated airOS-F logo
- changed GUI references from Config port to Management(MGMT) Port
- reorganized code for AF5 support


Version 1.5 (September 5, 2013)
--------------------------------------------
New Features:
- New: SNMP v1 Private MIB (read only)
- New: Ethernet flow control support (pause frames)
 
Improvements:
- Improved: Increased link capacity
- Improved: Main Page web layout changes
 
Fixes:
- Fix: UBNT Discovery protocol
- Fix: Cisco Discovery Protocol (CDP)
 
Notes:
- Note: Will not talk to Version 1.1.2 code - must update far end of link first if you are using the link to update the radios.


Version 1.1.2 - Final (February 21, 2013)
--------------------------------------------

Improvements:
- Improved: GiGE Support for more Cisco switches


Version 1.1.1 - Temperature Fix (January 10, 2013)
--------------------------------------------

Fixes:
- Fix: Improved Temperature compensation for Tx Power

Notes:
- Note: Will not talk to Version 1.0 code - must update far end of link first if you are using the link to update the radios.


Version 1.1 - Final (December 4, 2012)
--------------------------------------------

New Features:
- New: Jumbo Packet support (9600 bytes)
- New: Internal Link Characterization for coding enhancements
- New: 1/4 Rate Modulation for high fade conditions

Improvements:
- Improved: TCP/IP performance
- Improved: Performance When in Overload

Fixes:
- Fix: Stabilized Link Capacity Under Load
- Fix: Addressed Datapath Freeze Condition
- Fix: Fixed NTP
- Fix: Improved Ranging Accuracy
- Fix: Brazil Max Power-out Moved to 33dBm
- Fix: Disabled Low Power GIGE Modes
- Fix: Changed Australia and New Zealand to ACMA from ETSI
- Fix: GPS now displays longitude for both hemispheres
- Fix: Advertise speeds for fixed GIGE rates

Debug Features:
- Improved: Added information to support download
- Improved: Added manual control of GPS Radio

Notes:
- Note: Will not talk to Version 1.0 code - must update far end of link first if you are using the link to update the radios.

Version 1.0 - Initial Release (August 6, 2012)
--------------------------------------------

Fixes:
- Fix: Link Stability Issues
- Fix: Link Lockup Issues
- Fix: VLAN Connectivity Issues
- Fix: Local Management Access Issues

Notes:
- Note: Base airFiber software - please update if you are running 1.0-RC1