AirOS F Firmware Revision History ==================================================================== Supported products * airFiber 24/24HD ==================================================================== Changelog: -------------------------------------------- Version 4.0.3 (January 29th, 2018) -------------------------------------------- New Features: - none Improvements: - Security patch to address Read Only user privilege escalation Known Issues: - Ethernet Carrier Drop Block Data After Pulse does not work and should be disabled This is true for all releases where this feature exists Notes: - Recommend updating far end of link before near end -------------------------------------------- Version 4.0.2 (November 8th, 2017) -------------------------------------------- New Features: - none Improvements: - Fixed Static IP issue where static IP gateway was not programmed into router table Known Issues: - Ethernet Carrier Drop Block Data After Pulse does not work and should be disabled This is true for all releases where this feature exists Notes: - Recommend updating far end of link before near end -------------------------------------------- Version 4.0.1 (October 13th, 2017) -------------------------------------------- New Features: - none Improvements: - Fixed Static IP issue where DNS IPs were not being by new GUI after factory reset - Fixed issue where event names in engineering log were out of sync with actual event name Known Issues: - Spectrum Analyzer still Java based Notes: - Recommend updating far end of link before near end -------------------------------------------- Version 4.0 (August 29th, 2017) -------------------------------------------- New Features: - All New GUI - Immediate changes for Basic Wireless Settings; RF link maintained where possible - Added strict timing mode for improved co-location Improvements: - Full password length now used (not just first 8 characters) for both web and ssh/telnet - Ethernet Carrier drop now has high and low trigger points, new timers, etc - Various Security Updates Known Issues: - Spectrum Analyzer still Java based - If your configuration has ALL three of the characteristics listed: 1. You have inband management disabled 2. You have a management VLAN enabled 3. You manage a remote radio (far side of an airFiber RF link) by connecting the remote data port to the management port either directly or through a switched network you will need to enable inband management on the remote radio BEFORE you upgrade. After the upgrade, you can then reconnect to the remote radio and disable inband management. Failure to do so will leave the remote radio unmanageable over the RF link (local access via the management port will still function normally). Notes: - Recommend updating far end of link before near end - Only first 8 characters of old passwords are used after update - must reconfigure for longer passwords -------------------------------------------- Version 3.4-beta1 (June 3, 2016) -------------------------------------------- New Features: - Remote IP on mainpage is now a link to the paired radio Improvements: - n/a Fixes: - n/a Known Issues: - n/a Notes: - Recommend updating far end of link before near end -------------------------------------------- Version 3.2 (Nov 30, 2015) -------------------------------------------- New Features: - AC2 Support - Carrier Drop tracks Capacity - TDD Variable Duty Cycle - Actual/Ideal receive power shown on front page - Dataport can be disabled (please be careful) - Displays Framelength on Front Page Improvements: - AirView launch defaults to download and run locally - Improved airView interference detection time - Bring all airFiber radios up to a common release - Internal Cleanup/Organization Fixes: - Corrected Max EIRP to 23dBm for Bahrain - Address various airView Issues including unable to start, TCP port configuration, unresponsive radios - Modified Discovery protocol to report MAC address printed on unit Known Issues: - SSH password only use first 8 characters of login password - We are investigating possible modulation downgrade relative to pre-beta code - if you see this, please let us know Notes: - Duplex settings MUST be the same on both Master and Slave - Recommend updating far end of link before near end -------------------------------------------- Version 2.2.1 (July 17, 2015) -------------------------------------------- New Features: - n/a Improvements: - n/a Fixes: - Addresses vulterability that could allow unauthenticated users to gain access to the device via HTTP(s). All users should update immediately. Known Issues: - n/a. Notes: - n/a -------------------------------------------- Version 2.2 (January 5, 2015) -------------------------------------------- New Features: - Added Ethernet health monitoring for DATA port - Added airView support Improvements: - Signed airView Java Applet to run on newer Java installations without security exceptions - Receive signal bar now reads full scale for perfectly aimed link (was 3 db low) Fixes: - Fixed formatting errors in SNMP MIB - Fixed bug on system page where clicking "Check for Updates" would cause "Startup Date" field to become checked as well. - Fixed problem where ethernet link would never come back after an ethernet Carrier Drop event. - Fixed main page performance graph freeze on communication error - Changed min signal on bar graph to -90 Known Issues: - n/a Notes: - n/a Version 2.0 (March 28, 2014) -------------------------------------------- New Features: - added multicast filtering - added GIGE carrier follows RF link functionality - added Link up-time display - added Remote MAC address display - added Remote IP address display Improvements: - Obsoleted ability to read AES key from MIB - reorganized Main Page to simplify installation - distance reads in Km/Miles if 1 or greater - receive power graphs scale with link distance - reorganized Advanced Page - changed flow control verbage Fixes: - Fixed GIGE Carrier issue that required unit to be rebooted after enabling - Fixed Power limit issues for some ETSI regions - Fixed Rx power display issues for ETSI/ACMA regions This addressed an ETSI/ACMA issue where the received power displayed values that were 5dB too high. While the rx display is now correct, the actual tx power has not changed. Link performance should not be effected. - Fixed SNMP MIB issue found by openNMS - Modified Ethernet transciever programming to address CRC errors Notes: - removed Temperature readings - updated airOS-F logo - changed GUI references from Config port to Management(MGMT) Port - reorganized code for AF5 support Version 1.5 (September 5, 2013) -------------------------------------------- New Features: - New: SNMP v1 Private MIB (read only) - New: Ethernet flow control support (pause frames) Improvements: - Improved: Increased link capacity - Improved: Main Page web layout changes Fixes: - Fix: UBNT Discovery protocol - Fix: Cisco Discovery Protocol (CDP) Notes: - Note: Will not talk to Version 1.1.2 code - must update far end of link first if you are using the link to update the radios. Version 1.1.2 - Final (February 21, 2013) -------------------------------------------- Improvements: - Improved: GiGE Support for more Cisco switches Version 1.1.1 - Temperature Fix (January 10, 2013) -------------------------------------------- Fixes: - Fix: Improved Temperature compensation for Tx Power Notes: - Note: Will not talk to Version 1.0 code - must update far end of link first if you are using the link to update the radios. Version 1.1 - Final (December 4, 2012) -------------------------------------------- New Features: - New: Jumbo Packet support (9600 bytes) - New: Internal Link Characterization for coding enhancements - New: 1/4 Rate Modulation for high fade conditions Improvements: - Improved: TCP/IP performance - Improved: Performance When in Overload Fixes: - Fix: Stabilized Link Capacity Under Load - Fix: Addressed Datapath Freeze Condition - Fix: Fixed NTP - Fix: Improved Ranging Accuracy - Fix: Brazil Max Power-out Moved to 33dBm - Fix: Disabled Low Power GIGE Modes - Fix: Changed Australia and New Zealand to ACMA from ETSI - Fix: GPS now displays longitude for both hemispheres - Fix: Advertise speeds for fixed GIGE rates Debug Features: - Improved: Added information to support download - Improved: Added manual control of GPS Radio Notes: - Note: Will not talk to Version 1.0 code - must update far end of link first if you are using the link to update the radios. Version 1.0 - Initial Release (August 6, 2012) -------------------------------------------- Fixes: - Fix: Link Stability Issues - Fix: Link Lockup Issues - Fix: VLAN Connectivity Issues - Fix: Local Management Access Issues Notes: - Note: Base airFiber software - please update if you are running 1.0-RC1